Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

E.164 number on phone display

hello all,

I have cucm 7.1 cluster with an h.323 gateway.

I am having a problem with e.164 number.

When im getting international call, i can see the full e.164 number in my debugs, but i am not able to see full e.164 on ip phone. on ip phone its displaying number but without "+"

Please have alook on below debug isdn q931:

***********************************************************************

Channel ID i = 0xA98381

                Exclusive, Channel 1

        Display i = 'HQ1'

        Calling Party Number i = 0x0081, '+179236547890'

                Plan:Unknown, Type:Unknown

        Called Party Number i = 0xA1, '9271043004'

                Plan:ISDN, Type:National

Jan 13 09:57:36.786: ISDN Se0/1/0:23 Q931: Received SETUP  callref = 0x809A callID = 0x0016 switch = primary-ni interface = User

Jan 13 09:57:36.806: ISDN Se0/1/0:23 Q931: TX -> CALL_PROC pd = 8  callref = 0x809A

***********************************************************************

on ip phone im getting 179236547890.

I tried the same test with MGCP GW & CME Router & its working fine there .. but its not working on H.323 GW.


Can any body tell me wats the issue ?

Regards,

  • IP Telephony
10 REPLIES
Cisco Employee

E.164 number on phone display

What is the IP Phone model ? Is this issue specific to any perticular phone model or all models ?


GP.

Cisco Employee

E.164 number on phone display

& also post the phone firmware version.


GP.

New Member

Re: E.164 number on phone display

Phones model are 7961 & phone firmware version is SCCP41.8-4-1S

Gajan thanks for your reply

I dont think so its phone model or firmware version issue, because i just did the test by defining + in under Gateway option in CUCM & its displaying complete e.164 on phones display.

If its in debug isdn q931 then it should display on phone as well. Im confuse why its not displaying by default ?

Regarrds

Hall of Fame Super Silver

E.164 number on phone display

is the GW in CUCM defined with "All" significant digitis?

Are you performing any translations either on the GW or CUCM?

My recommendation would be to look at CUCM SDI trace logs to see what CUCM is seeing.

HTH,

Chris

New Member

E.164 number on phone display

Hi Chris,

Yes im doing translation on GW.

I have defined one translation rule for incoming call which is defined under voice-port.

voice transation-rule 1

rule 1 /.*\(....\)/ /\1/

voice translation-profile 1

translate called 1

voice-port 0/1/0:23

translation-profile incoming 1

dial-peer voice 1 pots

incoming called-number .

direct-inward-dial

!

dial-peer voice 2 voip

destination-pattern ^7...$

voice-class codec 1

voice-class h323 1

session target ipv4:142.100.64.12

dtmf-relay h245-alphanumeric

!

dial-peer voice 3 voip

preference 1

destination-pattern ^7...$

voice-class codec 1

voice-class h323 1

session target ipv4:142.100.64.11

dtmf-relay h245-alphanumeric

On GW i have confgured signifact digit 4

Regards,

Anis

Green

Re: E.164 number on phone display

My input was a mistake

Sorry

Regards, Alex. Please rate useful posts.
New Member

Re: E.164 number on phone display

Hello acampbell,

If i remove translation-profile from voice-port 0/1/0:23, then how my incoming call will work ?

I tried by removing translation-profile from voice-port & i defined it under dial-peer voice 1 .. still its the same situation

Regards,

Anis

New Member

Re: E.164 number on phone display

Hello Chris,

Can you tell me how to get the SDI trace logs of CUCM ?

Regards

Hall of Fame Super Silver

E.164 number on phone display

Use Real Time Monitor Tool to collect the CallManager service logs, it will gather SDI and SDL logs, look at the SDI.  There are some good guides on how to use RTMT on CCO for your specific version.

HTH, please rate all useful posts!

Chris

761
Views
5
Helpful
10
Replies