Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

E1 over 5ess switch type.

Is it possible to use a E1 over 5ess (5ess) isdn switch type ?

And if is possible, somebody have some ideia to do that ?

Ab

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Gold

Re: E1 over 5ess switch type.

Under controller E1, configure clock source internal.

Under serial interface, isdn protocol-emulate network.

Please remember to rate useful posts with the scrollbox below.

4 REPLIES
Hall of Fame Super Gold

Re: E1 over 5ess switch type.

It is possible, what exact problem are you trying to solve ?

New Member

Re: E1 over 5ess switch type.

I'm connecting my 2811 router with a Nortel PBX using a E1 connection and my D channel isn't getting up. see outputs bellow

----------------------------------

----------------------------------

sh conf

network-clock-participate wic 0

network-clock-select 1 E1 0/0/0

isdn switch-type primary-5ess

isdn gateway-max-interworking

controller E1 0/0/0

pri-group timeslots 1-2,16

interface Serial0/0/0:15

no ip address

encapsulation hdlc

isdn switch-type primary-5ess

isdn incoming-voice voice

isdn send-alerting

no cdp enable

----------------------------------

----------------------------------

gw-jlplda-0#sh isdn status

Global ISDN Switchtype = primary-5ess

ISDN Serial0/0/0:15 interface

dsl 0, interface ISDN Switchtype = primary-5ess

Layer 1 Status:

ACTIVE

Layer 2 Status:

TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED

Layer 3 Status:

0 Active Layer 3 Call(s)

Active dsl 0 CCBs = 0

The Free Channel Mask: 0x80000003

Number of L2 Discards = 0, L2 Session ID = 47

Total Allocated ISDN CCBs = 0

----------------------------------

----------------------------------

sh debug

gw-jlplda-0(config-controller)#

001891: *Oct 26 10:25:43: %CONTROLLER-5-UPDOWN: Controller E1 0/0/0, changed state to up

gw-jlplda-0(config-controller)#

001892: *Oct 26 10:25:45: %LINK-3-UPDOWN: Interface Serial0/0/0:15, changed state to up

gw-jlplda-0(config-controller)#

001893: *Oct 26 10:25:47: ISDN Se0/0/0:15 Q931: Ux_DLRelInd: DL_REL_IND received from L2

gw-jlplda-0(config-controller)#

001894: *Oct 26 10:25:48: %MARS_NETCLK-3-HOLDOVER: Exiting Holdover for Controller E1 0/0/0

gw-jlplda-0(config-controller)#

001895: *Oct 26 10:25:56: ISDN Se0/0/0:15 Q931: Ux_DLRelInd: DL_REL_IND received from L2

gw-jlplda-0(config-controller)#

001896: *Oct 26 10:26:05: ISDN Se0/0/0:15 Q931: Ux_DLRelInd: DL_REL_IND received from L2

gw-jlplda-0(config-controller)#BAD FRAME()

gw-jlplda-0(config-controller)#BAD FRAME()

gw-jlplda-0(config-controller)#BAD FRAME()

gw-jlplda-0(config-controller)#BAD FRAME()

gw-jlplda-0(config-controller)#

001897: *Oct 26 10:26:14: ISDN Se0/0/0:15 Q931: Ux_DLRelInd: DL_REL_IND received from L2

Hall of Fame Super Gold

Re: E1 over 5ess switch type.

Under controller E1, configure clock source internal.

Under serial interface, isdn protocol-emulate network.

Please remember to rate useful posts with the scrollbox below.

New Member

Re: E1 over 5ess switch type.

thanks so much.

sorted out !!

Ab

873
Views
5
Helpful
4
Replies