Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

e1 r2 configuration for thailand telco (true corp)

anyone have any sample?

it seems like they are using 2 different type of configuration for incoming and outgoing calls.

Got my outgoing call work by configured the following

---------------

controller E1 0/0/0

framing NO-CRC4

ds0-group 0 timeslots 1-15,17-31 type r2-digital dtmf dnis

-------------

If i used the same configuration for incoming, i got nothing. No calling and called number collected.

Got some hints from the telco, they provided sample configuration like

----

controller E1 0/0/0

framing no-crc4

clock source line

ds0-group 1 timeslots 1-15,17-31 type r2-digital r2-compelled ani

cas-custom 1

country thailand

category 2

answer-signal group-b 1

caller-digits 4

-----

and

-----

controller E1 0/0/0

framing no-crc4

clock source line

ds0-group 1 timeslots 1-15,17-31 type r2-digital r2-compelled ani

cas-custom 1

country thailand

category 2

answer-signal group-b 1

dnis-digits min 1 max 4

groupa-callerid-en

---------

Both doesn't works.

Debug shows that it collected "3" , the number i was trying to reach was 35XX

Jun 19 16:13:10.455: htsp_process_event: [0/0/0:1(12), R2_Q421_IDLE, E_DSP_SIG_0000]

Jun 19 16:13:10.455: r2_q421_ic_seize(0/0/0:1(12)) Rx SEIZURE

Jun 19 16:13:10.459: r2_reg_start_digit_collection(0/0/0:1(12))

Jun 19 16:13:10.459: r2_q421_ic_seize(0/0/0:1(12)) Tx SEIZE ACK (with 100ms delay)vnm_dsp_set_sig_state:[R2 Q.421 0/0/0:1(12)] set signal state = 0x8vnm_dsp_set_sig_state:[R2 Q.421 0/0/0:1(12)] set signal state = 0xC

Jun 19 16:13:10.459: htsp_timer - 2000 msec

Jun 19 16:13:10.459: r2_reg_process_event: [0/0/0:1(12), R2_REG_IDLE, E_R2_REG_START_COLLECTION(93)]

Jun 19 16:13:10.459: r2_reg_start_collecting(0/0/0:1(12))

Jun 19 16:13:10.459: r2_reg_timer_stop(0/0/0:1(12))

Jun 19 16:13:10.459: htsp_process_event: [0/0/0:1(12), R2_Q421_IC_SEIZE, E_HTSP_SETUP_ACK]

Jun 19 16:13:10.459: r2_q421_ic_setup(0/0/0:1(12)) E_HTSP_SETUP_ACK

Jun 19 16:13:10.459: htsp_timer_stop

Jun 19 16:13:10.459: r2_reg_offhook(0/0/0:1(12))

Jun 19 16:13:10.459: r2_reg_process_event: [0/0/0:1(12), R2_REG_COLLECTING, E_R2_REG_OFFHOOK(94)]

Jun 19 16:13:10.459: r2_reg_ic_offhook(0/0/0:1(12))

Jun 19 16:13:10.459: R2 Incoming Voice(0/0): DSX (E1 0/0/0:11): STATE: R2_IN_IDLE R2 Got Event R2_START

Jun 19 16:13:10.671: htsp_digit_ready_up(0/0/0:1(12)): Rx digit='3'

Jun 19 16:13:10.671: R2 Incoming Voice(0/0): DSX (E1 0/0/0:11): STATE: R2_IN_COLLECT_DNIS R2 Got Event 3

Jun 19 16:13:10.671: r2_reg_generate_digits(0/0/0:1(12)): Tx digit '1'

Jun 19 16:13:10.767: htsp_digit_ready(0/0/0:1(12)): Rx digit='#'

Jun 19 16:13:10.767: R2 Incoming Voice(0/0): DSX (E1 0/0/0:11): STATE: R2_IN_COLLECT_DNIS R2 Got Event R2_TONE_OFF

Jun 19 16:13:10.767: r2_reg_generate_digits(0/0/0:1(12)): Tx digit '#'

Jun 19 16:13:13.671: R2 Incoming Voice(0/0): DSX (E1 0/0/0:11): STATE: R2_IN_COLLECT_DNIS R2 Got Event R2_TONE_TIMER

Jun 19 16:13:13.671: r2_reg_generate_digits(0/0/0:1(12)): Tx digit '3#'

Jun 19 16:13:20.671: htsp_dialing_done(0/0/0:1(12))

Jun 19 16:13:20.771: htsp_digit_ready_up(0/0/0:1(12)): Rx digit='5'

Jun 19 16:13:20.771: R2 Incoming Voice(0/0): DSX (E1 0/0/0:11): STATE: R2_IN_CATEGORY R2 Got Event 5

Jun 19 16:13:20.771: Enter r2_comp_category

Jun 19 16:13:20.771:  R2 Event : 5

Jun 19 16:13:20.771:  ####### collect_call_enable = 0

Jun 19 16:13:20.771: ######## Not Sending B7 ##################

Jun 19 16:13:20.771: r2_reg_event_proc(0/0/0:1(12)) ADDR_INFO_COLLECTED (DNIS=3, ANI=)

Jun 19 16:13:20.771: r2_reg_process_event: [0/0/0:1(12), R2_REG_COLLECTING, E_R2_REG_ADDR_COLLECTED(88)]

Jun 19 16:13:20.771: r2_reg_ic_addr_collected(0/0/0:1(12))htsp_switch_ind

Jun 19 16:13:20.771: //-1/85A096A48054/CCAPI/cc_api_display_ie_subfields:

it seems like it came in but too long later. anyone have any idea or have a sample config that works with this telco?

Everyone's tags (6)
483
Views
0
Helpful
0
Replies
CreatePlease to create content