Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

E1 R2 digital Call SETUP Trobleshooting

Failure to make and recieve external calls

We noticed that a lot of ports remains at blocked at IN STATUS.

BAX-MTY#sh voice port summary

IN OUT

PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC

=============== == ============ ===== ==== ======== ======== ==

0/0/0:1 17 r2-digital up up blocked idle y

0/0/0:1 18 r2-digital up up blocked idle y

0/0/0:1 19 r2-digital up up clearfwd idle y

0/0/0:1 20 r2-digital up dorm idle idle y

0/0/0:1 21 r2-digital up dorm idle idle y

0/0/0:1 22 r2-digital up dorm idle idle y

0/0/0:1 23 r2-digital up dorm idle idle y

0/0/0:1 24 r2-digital up dorm idle idle y

0/0/0:1 25 r2-digital up dorm idle idle y

0/0/0:1 26 r2-digital up dorm idle idle y

0/0/0:1 27 r2-digital up dorm idle idle y

0/0/0:1 28 r2-digital up dorm idle idle y

0/0/0:1 29 r2-digital up dorm idle idle y

0/0/0:1 30 r2-digital up up blocked idle y

0/0/0:1 31 r2-digital up up blocked idle y

I looked the following thread but I did't find something to change in my configuration.

http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Service%20Providers&topic=Voice%20over%20IP&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.1dde596b

Anyone knows what is the posible cause?

I attach the configuration and debug

Thanks

4 REPLIES
Hall of Fame Super Gold

Re: E1 R2 digital Call SETUP Trobleshooting

IOS version used ?

New Member

Re: E1 R2 digital Call SETUP Trobleshooting

!!! UPDATE !!!

There is an update related to this topic:

The problem was corrected on the Service Provider side ... they corrected some parameters inside their network Infrastructure.

This is the IOS Version:

Version 12.4(17)

flash:c2800nm-advipservicesk9-mz.124-17.bin

Thanks

Green

Re: E1 R2 digital Call SETUP Trobleshooting

Checking different customer configs and Telmex recommendation, and all points to this configuration: (Just change channels used)

controller E1 0/1

framing NO-CRC4

ds0-group 1 timeslots 1-15,17-31 type r2-digital r2-compelled ani

cas-custom 1

country telmex

category 2

answer-signal group-b 1

***********************************************************************

Please give it a try at the following config:

controller E1 1/0

framing NO-CRC4

clock source line

line-termination 75-ohm

ds0-group 0 timeslots 1-8 type r2-digital r2-compelled ani

cas-custom 0

country telmex

seizure-ack-time 30

category 2

answer-signal group-b 1

dnis-digits min 4 max 4

dnis-complete

timer interdigit incoming 1000

groupa-callerid-end

voice-port 1/0:0

cptone mexico

Check the following:

For inbound calls from Telmex to router you can configure

dnis-digits min x max y

timer interdigit incoming 1000

This will reduce the interdigit timer to 1 sec and we will collect between x and y digits from pbx for the dnis.

Have you already made a loopback test?

Let us know

New Member

Re: E1 R2 digital Call SETUP Trobleshooting

Thanks, I appreciate your advice ... I analyzed your configuration, It seems very useful and I will be using it next time.

I already posted an update about this topic and the problem was corrected on the Service Provider side. I appreciate your help!

Thanks

866
Views
5
Helpful
4
Replies