04-17-2008 11:24 PM - edited 03-15-2019 10:08 AM
Hi,
I have Cisco 2811 router with VWIC-2MFT-E1. One port is for PBX and other one is for Telco PRI line. My Telco Number is 8664900 with 100 DID. I dial this number and router answer the call. I want to transfer all incoming call from Telco line to PBX PRI line.
I do this with connection plar. Under Telco PRI voice-port i write connection-plar 8664900 and transfer all call the pots dial peer. Under pots dial peer forward 3 digit of number to PBX voice-port. But this configuration only transfer one DID to PBX. I want all incoming DID to forward PBX voice-port. For example when i call 8664900, 8664901, 8664902 numbers i should send 900, 901, 902 ... to PBX. How should resolve this problem. I am sending my configuration. Thank you...
TELCO PORT
voice-port 0/0/0:15
connection-plar 8664900
PBX PORT
voice-port 0/0/1:15
input gain 4
output attenuation 4
cptone TR
timeouts interdigit 2
description Connect To PBX
bearer-cap Speech
FOR CALL TRANSFER
dial-peer voice 14 pots
description *****TELCO_TO_LG_PBX*****
destination-pattern 86649..
no digit-strip
direct-inward-dial
forward-digits 3
Ufuk Guler
04-24-2008 06:25 AM
You need "isdn number called enbloc XX" . Please send output of "debug isdn q931" with "term mon". Also check "show controllers e1" as you may have slips withiut the needed "network-clock-participate" and network-clock-select" commands.
05-08-2008 03:05 PM
Hi Guler
I already worked with a similar scenario.
The only diference was that When I received the GDN number from PSTN, it must have ring on the extension Cisco.
You have to talk with PBX staff if you need a OVERLAPPING OR ENBLOC,in my case was OVERALPPING.
The CallManger and PBX Ericsson use the access code 64T for calls to PSTN.
Below you will find the dial-peers:
!
controller E1 0/0/0
pri-group timeslots 1-31
description E1 ISDN PRI TELEMOVIL
!
controller E1 0/0/1
clock source internal
pri-group timeslots 1-31
description E1 ISDN PRI PBX
!
!
!
interface Serial0/0/0:15
no ip address
isdn switch-type primary-net5
isdn incoming-voice voice
no cdp enable
!
interface Serial0/0/1:15
no ip address
isdn switch-type primary-net5
isdn overlap-receiving T302 2000
isdn protocol-emulate network
isdn incoming-voice voice
isdn bchan-number-order descending
no cdp enable
!
!
!
voice-port 0/0/0:15
!
voice-port 0/0/1:15
!
!
dial-peer voice 1 pots
description Enable DID for PSTN Trunk
incoming called-number .
direct-inward-dial
port 0/0/0:15
!
dial-peer voice 2 pots
description Enable DID for PBX Trunk
incoming called-number .
direct-inward-dial
port 0/0/1:15
!
dial-peer voice 3 pots
description Calls from PSTN to PBX
destination-pattern 1...
port 0/0/1:15
forward-digits all
!
dial-peer voice 4 voip
tone ringback alert-no-PI
description Calls to CCM
destination-pattern 2...
progress_ind setup enable 3
voice-class codec 4
session target ipv4:10.3.0.25
dtmf-relay h245-alphanumeric
no vad
!
dial-peer voice 5 pots
description Outgoing Calls to Telemovil
destination-pattern 64T
progress_ind setup enable 3
progress_ind alert enable 8
direct-inward-dial
port 0/0/0:15
!
dial-peer voice 2507100 pots
description GDN:2507100 TO DN:2000
translation-profile incoming pstn-incoming10
incoming called-number 1000
direct-inward-dial
port 0/0/0:15
!
REGARDS
WALTER FLORES
06-08-2008 02:19 AM
Hi Walter,
Many thanks for answer. I solved my problem using another PBX PRI card. I connect Telco line to this card. And PBX answering incoming PRI calls. But as soon as possible i try your solution. Thank you...
Ufuk Guler.
05-09-2008 05:56 AM
When you're working to get this set up, redirect your debug isdn q931 messages to the PRI debugger from download.com - it'll make it much easier to see what's going on.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: