Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Error msg %HWIC_CDSX_MODULE-3-CDSX_IPC_CMD_FAIL:

Hi,

I just installed a NM-HD-2V (with a SM-NM-ADPTR) in a 2911 router, and now during bootup process I have the following msg:

000062: *Jun  1 18:38:22.323: %HWIC_CDSX_MODULE-3-CDSX_IPC_CMD_FAIL: IPC Command (message type:0x1, opcode:0xD) to the firmware Failed on slot(0) subslot(0) due to IPC Hold Q Full

000063: *Jun  1 18:38:22.323: %HWIC_CDSX_MODULE-3-CDSX_IPC_CMD_FAIL: IPC Command (message type:0x1, opcode:0xD) to the firmware Failed on slot(0) subslot(0) due to IPC Hold Q Full

In slot(0) subslot(0) I have a VWIC3-4MFT-T1/E1,

I do not remember to have seen this msg before, the only recent change is the new NM-HD-2V.

I just want to know what this message means and if is something that I have to worry about or not.

Here is the #sh invent

TEST1#sh inventory

NAME: "CISCO2911/K9 chassis", DESCR: "CISCO2911/K9 chassis"

PID: CISCO2911/K9      , VID: V02 , SN:

NAME: "VWIC3-4MFT-T1/E1 - 4-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0", DESCR: "VWIC3-4MFT-T1/E1 - 4-Port RJ-48 Multiflex Trunk - T1/E1"

PID: VWIC3-4MFT-T1/E1  , VID: V01 , SN:

NAME: "2nd generation four port FXO voice interface daughtercard on Slot 0 SubSlot 1", DESCR: "2nd generation four port FXO voice interface daughtercard"

PID: VIC2-4FXO         , VID: V03 , SN:

NAME: "2nd generation four port FXO voice interface daughtercard on Slot 0 SubSlot 2", DESCR: "2nd generation four port FXO voice interface daughtercard"

PID: VIC2-4FXO         , VID: V04 , SN:

NAME: "VWIC3-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 3", DESCR: "VWIC3-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1"

PID: VWIC3-2MFT-T1/E1  , VID: V01 , SN:

NAME: "PVDM3 DSP DIMM with 128 Channels on Slot 0 SubSlot 4", DESCR: "PVDM3 DSP DIMM with 128 Channels"

PID: PVDM3-128         , VID: V01 , SN:

NAME: "PVDM3 DSP DIMM with 64 Channels on Slot 0 SubSlot 5", DESCR: "PVDM3 DSP DIMM with 64 Channels"

PID: PVDM3-64          , VID: V01 , SN:

NAME: "Network Module Adapter for SM Slot on Slot 1", DESCR: "Network Module Adapter for SM Slot"

PID: SM-NM-ADPTR       , VID: V01, SN:

NAME: "High Density Analog Voice Network Module on Slot 1", DESCR: "High Density Analog Voice Network Module"

PID: NM-HD-2V          , VID: V01 , SN:

NAME: "2nd generation four port FXO voice interface daughtercard on Slot 1 SubSlot 0", DESCR: "2nd generation four port FXO voice interface daughtercard"

PID: VIC2-4FXO         , VID: V04 , SN:

NAME: "C2911 AC Power Supply", DESCR: "C2911 AC Power Supply"

PID: PWR-2911-AC       , VID: V03 , SN:

TEST1#

Thanks in advance.

Regards

Carlito

264
Views
0
Helpful
0
Replies