Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Extension Mobility

i configure extension mobility,anytime i go to the phoen and press the service botton i see the extension mobility there but when i select it is telling host not found,and i configure the redundancy for my callmanager too anytime i put the publisher off the phones go off.need help

15 REPLIES

Re: Extension Mobility

First, replace all the hostname with publisher IP from Enterprise Parameters.

Second, check you IP phone whether it's locating for pub as 'active' and sub as 'standby' from Device Configurationn>CallManager Configuration.

HTH.

Re: Extension Mobility

Also did you add all of your CUCM at System>Cisco Unified CallManager?

If you have added, make a group with one pub+one sub from System>Cisco Unified CallManager Groups.

Did you create any device pool? If yes, add that CallManager Group in the device pool.

Add your phone to that device pool from phone config.

Hope this help. Please rate if helpful.

New Member

Re: Extension Mobility

I created one callmanager group and i added all the 2 callmanager to the same group.

New Member

Re: Extension Mobility

yeah i've replaced all host with publisher ip addresses,and it replicate on the suscriber too,and the publisher ip is the primary on all the phones,any ideas

Re: Extension Mobility

Hi,

I have just configured the EM on my CUCM, and found no problem, crosscheck with me please:

Go to System>Enterprise Parameters

Check the 'URL Service' entry under 'Phone URL Parameter'.

By default it is set like:

http://LABCUCM/CCMCIP/getservicesmenu.asp (assuming the hostname is LABCUCM)

And you have replaced the LABCUCM with IP like:

http://10.10.10.10/CCMCIP/getservicesmenu.asp

And also don't forget to reset your subscribed phone after changing this settings.

Cisco Employee

Re: Extension Mobility

if you're using 6.1(2) and you're looking for EM resiliency you do need to use hostnames and perform the name resolution with your DNS server to choose secondary server if primary is not responding

HTH

java

if this helps, please rate

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
New Member

Re: Extension Mobility

Thank u very much,the extension mobility is working now,i can log in but i can log out on the phone but in the callmanager i can do so and the backup i configired is still not working,anytime i restart the Publisher the phones too restart,any ideas.

Re: Extension Mobility

That's listening great! Which change in settings made you working EM, please share.

Your second problem is not clear, is it related with EM? When your pub is down, can your phone find the sub?

New Member

Re: Extension Mobility

ok,first my EM is working but i can not loggoff from the phone which is not right,i can login using my username and passworg and when i click the service botton again to loggoff i can see anything there,second i configure cluster but it si not working because when i restart the Publisher the phones to restart it' mean the Subscriber is not working,so i need help.

Cisco Employee

Re: Extension Mobility

you're still lacking configuration, your device profile must be subscribed to EM to logout. it's all outlined in the EM config guide, please read the guides

HTH

java

if this helps, please rate

HTH

java

if this helps, please rate

www.cisco.com/go/pdi

Re: Extension Mobility

About the second problem, your clustering is not configured properly.

1. Add both (pub+sub) of the CUCM at System>Cisco Unified CallManager Group

2. Select the same group at System>Device Pool

3. Add your phone at the same device pool from Phone Config

4. Reset all phones from device pool

4. Check at phone whether 'Primary TFTP Server' is publisher and 'Standby TFTP Server' is subscriber. If it is not, then clustering is not completed.

New Member

Re: Extension Mobility

let me exlpain what i did,i name my callmanagers and i created the one groupe and i added the two callmanager to the same group and at the device pool creation i choose the name of the callmanager group i create,and at the phone end the ip address op the publisher is the primary and subscriber is the secondary,and still i dont know why if i restarted the publisher the phones to restart,any i deas.

Re: Extension Mobility

Can you make sure the 'Cisco CallManager' service is up and running in the sub?

New Member

Re: Extension Mobility

yes all the services are running in the Sub and Pub.

New Member

Re: Extension Mobility

Hi,

can you configure your CMgroup with sub as primary and pub as secondry..ie...sub ip first in the list

then restart the pub ....what is happening?...and then try with restarting sub-this is same as your previous config, only diff is sub became the primary

Thanks,

263
Views
0
Helpful
15
Replies