Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Fax CCME

Hi NetPro

I have a CCME whit one E1 ti connect to PSTN, inside have a ATA186 connect to FAX, when i send FAX to ATA number the call fail.

ISDN Call debug

.Sep 10 16:12:36.423: ISDN Se0/0/0:15 Q931: RX <- SETUP pd = 8 callref = 0x0A96

Sending Complete

Bearer Capability i = 0x8090A3

Standard = CCITT

Transfer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA18384

Preferred, Channel 4

Calling Party Number i = 0x80, '22442013'

Plan:Unknown, Type:Unknown

Called Party Number i = 0x80, '5834010'

Plan:Unknown, Type:Unknown

Low Layer Compat i = 0x8090A3

.Sep 10 16:12:36.439: ISDN Se0/0/0:15 Q931: TX -> CALL_PROC pd = 8 callref = 0x8A96

Channel ID i = 0xA98384

Exclusive, Channel 4

.Sep 10 16:12:36.447: ISDN Se0/0/0:15 Q931: TX -> ALERTING pd = 8 callref = 0x8A96

Progress Ind i = 0x8188 - In-band info or appropriate now available

.Sep 10 16:12:43.591: %ISDN-6-CONNECT: Interface Serial0/0/0:3 is now connected to 22442013 N/A

.Sep 10 16:12:43.591: ISDN Se0/0/0:15 Q931: TX -> CONNECT pd = 8 callref = 0x8A96

.Sep 10 16:12:43.599: ISDN Se0/0/0:15 Q931: RX <- CONNECT_ACK pd = 8 callref = 0x0A96

.Sep 10 16:12:49.591: %ISDN-6-CONNECT: Interface Serial0/0/0:3 is now connected to 22442013 N/A

.Sep 10 16:13:17.912: ISDN Se0/0/0:15 Q931: RX <- DISCONNECT pd = 8 callref = 0x0A96

Cause i = 0x8091 - User busy

.Sep 10 16:13:17.912: %ISDN-6-DISCONNECT: Interface Serial0/0/0:3 disconnected from 22442013 , call lasted 34 seconds

.Sep 10 16:13:17.912: ISDN Se0/0/0:15 Q931: TX -> RELEASE pd = 8 callref = 0x8A96

.Sep 10 16:13:17.920: ISDN Se0/0/0:15 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x0A96

Cause i = 0x8090 - Normal call clearing

Any Idea?

fixie rider
  • IP Telephony
5 REPLIES

Re: Fax CCME

My only idea is that the fax machine you're calling is already on a call and is busy. Sometimes fax machines take a bit of time after the last fax has hung up.

Here, it looks like a simply busy. I'm betting if you had called with an analog phone instead of a fax you would have had the same problem.

-nick

New Member

Re: Fax CCME

The fax it's not busy, when i call at fax have ring and fax tone... but when send a fax the call fail.

regards

fixie rider
Hall of Fame Super Gold

Re: Fax CCME

Please send output of "show controllers E1". You may have slips due to lack of network-clock commands.

New Member

Re: Fax CCME

Hi

Attach the command show controller e1

CME-sysasap#show controllers e1

E1 0/0/0 is up.

Applique type is Channelized E1 - balanced

No alarms detected.

alarm-trigger is not set

Version info Firmware: 20070321, FPGA: 13, spm_count = 0

Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.

CRC Threshold is 320. Reported from firmware is 320.

Data in current interval (498 seconds elapsed):

0 Line Code Violations, 0 Path Code Violations

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Total Data (last 24 hours)

0 Line Code Violations, 0 Path Code Violations,

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Regards

fixie rider
Hall of Fame Super Gold

Re: Fax CCME

No slips. Are you using H.323 or SCCP on the ATA ? The first is preferred and you should apply the config from "troubleshooting ata fax" (search).

216
Views
0
Helpful
5
Replies
This widget could not be displayed.