07-12-2010 11:20 AM - edited 03-15-2019 11:40 PM
Using a Cisco 2901 ISR configured for H323 connecting to CUCM 7.x - Using H323 for caller-id support on the FXO ports. It's a VIC2-2FXO and both inbound/outbounds calls is working fine. However, when an inbound call is made and not answered, the FXO port remains on an off-hook state and it will work once we shut and no shut the voice-port 0/0/0 and voice-port 0/0/1
Version: 15.1(1)T
PVDM-16
voice-card 0
dspfarm
dsp services dspfarm
no local-bypass
voice-port 0/0/0
input gain 3
timing hookflash-out 50
timing sup-disconnect 50
connection plar 6535
caller-id enable
!
voice-port 0/0/1
input gain 3
timing hookflash-out 50
timing sup-disconnect 50
connection plar 2536
caller-id enable
sccp local Vlan10
sccp ccm 172.16.17.30 identifier 2 priority 2 version 4.1
sccp ccm 172.16.17.35 identifier 1 priority 1 version 4.1
sccp
!
sccp ccm group 100
associate ccm 1 priority 1
associate ccm 2 priority 2
associate profile 10 register CFB5475d003542b
!
dspfarm profile 10 conference
description Site_Conferencing
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 2
associate application SCCP
!
dial-peer voice 100 pots
description PSTN dial-peer 1
preference 1
destination-pattern .T
incoming called-number .
port 0/0/0
forward-digits all
!
dial-peer voice 101 pots
description PSTN dial-peer 2
preference 2
destination-pattern .T
port 0/0/1
forward-digits all
!
dial-peer voice 1 voip
destination-pattern 6534
session target ipv4:172.16.17.30
incoming called-number .
dtmf-relay h245-alphanumeric
no vad
!
dial-peer voice 2 voip
destination-pattern 2536
session target ipv4:172.16.17.30
incoming called-number .
dtmf-relay h245-alphanumeric
no vad
char1#show voice call summ
PORT CODEC VAD VTSP STATE VPM STATE
============== ========= === ==================== ======================
0/0/0 None - S_CONNECT FXOLS_CONNECT
0/0/1 None - S_CONNECT FXOLS_OFFHOOK
50/0/1 .1 - - - EFXS_ONHOOK
50/0/1 .2 - - - EFXS_ONHOOK
50/0/2 .1 - - - EFXS_ONHOOK
50/0/2 .2 - - - EFXS_ONHOOK
50/0/3 .1 - - - EFXS_ONHOOK
50/0/3 .2 - - - EFXS_ONHOOK
char1#show voice call status
CallID CID ccVdb Port Slot/DSP:Ch Called # Codec MLPP Dial-peers
0x158 1494 0x31739DFC 0/0/0 No DSP 6534 None 100/101
0x15A 1494 0x2A18C040 0/0/1 No DSP *6534 None 101/100
1 active call found
07-12-2010 12:59 PM
Check: http://www.cisco.com/en/US/tech/tk652/tk653/technologies_tech_note09186a00800ae2d1.shtml
You need to configure custom tones for your country.
If you want a permanent solution, use ISDN, not analog.
01-31-2012 12:44 AM
Hi,
I was having similar problem in one of our site. Even after PSTN user disconnects the ip phone keeps on ringing.
I applied the custom tone settings. It really worked for me.
Thanks Paolo...
voice class custom-cptone FXO
dualtone disconnect
frequency 400
cadence 504 496
voice-port 0/0/0
supervisory disconnect dualtone mid-call
supervisory custom-cptone FXO
cptone SA
timeouts call-disconnect 1
timeouts wait-release 2
timing hookflash-out 50
connection plar 6123
caller-id enable
Regards,
Raffi.
01-31-2012 04:34 AM
You're welcome, thanks for the nice rating and good luck!
02-27-2016 02:27 AM
Hi,
I have the following configuration cisco 2811 H.323 gateway with CUCM 10.5.2 having FXO line.
i have same issue. line remains busy and end user remains getting disconnect tune.
!
voice-port 0/3/0
translation-profile incoming from-PSTN
input gain 14
compand-type a-law
no comfort-noise
cptone AE
timeouts call-disconnect 0
timeouts ringing 30
timeouts wait-release 1
connection plar opx 525
caller-id enable
!
dial-peer voice 1 pots
incoming called-number .
direct-inward-dial
forward-digits all
!
dial-peer voice 9 pots
description ==PSTN==
destination-pattern .T
port 0/3/0
!
dial-peer voice 100 voip
description ==DP for 1xx==
service session
destination-pattern 1..
session target ipv4:10.172.192.1
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
!
dial-peer voice 555 voip
service session
destination-pattern 525
session target ipv4:10.172.192.1
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
!
if i add "supervisory disconnect anytone" under voice-port then issue resolves but incoming calls disconnect after 1 or 2 seconds.
please advise what to do to fix the issue. thank you
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: