Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

FXO - Stats - Uc500

Is there any way to have a graph or other nice stats to figure out the FXO utilisation.

I think that I have too much FXO line for my needs and I would like to gather more information...

I have a Uc500

5 REPLIES
Community Member

Re: FXO - Stats - Uc500

Hi Philippe,

I tried to do this one time using SNMP and almost had it.

Unlike ISDN, we do not have a useful active calls mib to graph - unless I completely missed it!

The closest I could get was the voip call active table mib:

1.3.6.1.4.1.9.9.63.1.3.2

http://tools.cisco.com/Support/SNMP/do/BrowseOID.do?local=en&translate=Translate&objectInput=cvVoIPCallActiveTable

This lists all the active call legs - rather than a nice integer of the number of calls!

So my task was to create a script that determines the number of calls from this table.  Needless to say I had better things to do and forgot all about it.

I hope my past failure offers you some guidance!

Regards, Ash.

Community Member

Re: FXO - Stats - Uc500

I have try to type this OID on PRTG or on a simple software as MIB-browser and it did'nt find anything on the UC500.

Doest someone can find the state of a FXO on a uc500 with a specific OID ?

thanks

Community Member

Re: FXO - Stats - Uc500

Hi Philippe,

I have hunted around for this again and found a more promising oid:

1.3.6.1.4.1.9.9.62.1.3.2

I have tested this on a 2801 with vic2-4fxo and it displays the on-hook status.

Check whether this works for your UC500!

Regards, Ash.


Community Member

Re: FXO - Stats - Uc500

The closest OID'S that i have is this :

[1.3.6.1.4.1.9.9.62.1.3.2.1.1.19] = 1
[1.3.6.1.4.1.9.9.62.1.3.2.1.1.20] = 1
[1.3.6.1.4.1.9.9.62.1.3.2.1.1.21] = 1
[1.3.6.1.4.1.9.9.62.1.3.2.1.1.22] = 1
[1.3.6.1.4.1.9.9.62.1.3.2.1.1.23] = 1
[1.3.6.1.4.1.9.9.62.1.3.2.1.1.24] = 1
[1.3.6.1.4.1.9.9.62.1.3.2.1.1.25] = 1
[1.3.6.1.4.1.9.9.62.1.3.2.1.1.26] = 1
[1.3.6.1.4.1.9.9.62.1.3.2.1.1.27] = 1
[1.3.6.1.4.1.9.9.62.1.3.2.1.1.28] = 1
[1.3.6.1.4.1.9.9.62.1.3.2.1.2.19] = 2
[1.3.6.1.4.1.9.9.62.1.3.2.1.2.20] = 2
[1.3.6.1.4.1.9.9.62.1.3.2.1.2.21] = 2
[1.3.6.1.4.1.9.9.62.1.3.2.1.2.22] = 2
[1.3.6.1.4.1.9.9.62.1.3.2.1.2.23] = 2

Community Member

Re: FXO - Stats - Uc500

this is it ! when I call , those that have a value of one goes to 2

430
Views
0
Helpful
5
Replies
CreatePlease to create content