Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

FXS Port 0 has no dial tone FXS Port 1 has dial

     For some reason port 0 on my FXS card does not provide dialtone.  The settings on port 0 and port 1 are identical and I have swapped out analog phones

Symtoms

I can call the phone attached to port 0 from port 1 on the same card.

The LED associated with port 0 comes on when the phone goes off the hook. 

On port 0 the phone goes off hook, on hook, then off everytime I pick up the phone.

Any Ideas

Everyone's tags (5)
1 ACCEPTED SOLUTION

Accepted Solutions
Silver

Re: FXS Port 0 has no dial tone FXS Port 1 has dial

If you have "direct-inward-dial" configured under the FXO/FXS dial peers, remove them and try again.

MK

6 REPLIES
Silver

Re: FXS Port 0 has no dial tone FXS Port 1 has dial

If you have "direct-inward-dial" configured under the FXO/FXS dial peers, remove them and try again.

MK

New Member

Re: FXS Port 0 has no dial tone FXS Port 1 has dial

Your solution worked, thank you.  Any ideas on how to get call through to the FXS ports directly using DID numbers? When I remove the DID command from the dial-peer and try to dial in I get a second dialtone.

Silver

Re: FXS Port 0 has no dial tone FXS Port 1 has dial

Do you have connection plar configured under the voice port?

voice-port 0/1/0

connection plar 1234 (extension where the call will be terminated)

MK

New Member

Re: FXS Port 0 has no dial tone FXS Port 1 has dial

I am running CME on both routers and I am trying to place a call from WYRT1 to AZRT1 through the national or international pots dial-peer to a FXS port on AZRT1 with multiple numbers
No commands have been entered under the FXS Port.  I wanted to point multiple numbers to this FXS port and I wasn't sure if PLAR would be able to do this


hostname WYRT1

...Limited output.....

dial-peer voice 8 pots
description NATIONAL CALLING
preference 1
destination-pattern 91..........
direct-inward-dial
port 3/0:23
forward-digits 10
!
dial-peer voice 9 pots
corlist outgoing INT
description INTERNATIONAL CALLING
preference 1
destination-pattern 9011T
direct-inward-dial
port 3/0:23
prefix 011


...Limited output.....

hostname AZRT1


...Limited output.....

dial-peer voice 8 pots
description NATIONAL CALLING
preference 1
destination-pattern 91[29]..[29]......
direct-inward-dial
port 1/0:23
forward-digits 10
!
dial-peer voice 9 pots
description INTERNATIONAL CALLING
preference 1
destination-pattern 9011T
direct-inward-dial
port 1/0:23
prefix 011

dial-peer voice 1 pots
preference 1
destination-pattern 7573683333
direct-inward-dial
port 2/0
forward-digits all
!
dial-peer voice 2 pots
preference 1
destination-pattern 0112223334444555
direct-inward-dial
port 2/0
forward-digits all
!
dial-peer voice 3 pots
preference 1
destination-pattern 7184415453
direct-inward-dial
port 2/0
forward-digits all


...Limited output.....

Silver

Re: FXS Port 0 has no dial tone FXS Port 1 has dial

Replace the extension with "X".  If your extensions are 4 digits then use "Connection plar XXXX" under voice port. This will mach any 4 digits number.

voice-port x/y/z

connection plar XXXX opx

MK

New Member

Re: FXS Port 0 has no dial tone FXS Port 1 has dial

Sorry for the delay in communication. 

Thank you for the suggestion but I was trying to setup this port to have multiple different numbers which do not fall into any specific range. 

Example  800-555-1212, 214-728-2839, 0112833782901 all point to fxs port 0/1.  I would like to have call routed through the PRI and the have the phone ring directly.

4223
Views
0
Helpful
6
Replies
CreatePlease to create content