Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Gateway Configuration on CUCM v8

Hello,

i have configured mgcp on my cucm v8 using a 2901 router as the gateway, but calls are neither coming in nor going out. After debuging i recieve the error below.

Any ideas please.

Thanks

Jan  4 11:37:48.144: //-1/xxxxxxxxxxxx/MGCP/mgcp_check_hostname(8936):[lvl=0]Trying to validate endpoint name

Jan  4 11:37:48.148: ISDN Se0/0/1:15 Q931: TX -> SETUP pd = 8  callref = 0x000B

        Sending Complete

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA9839F

                Exclusive, Channel 31

        Calling Party Number i = 0x0081, '4621198'

                Plan:Unknown, Type:Unknown

        Called Party Number i = 0x80, '08039687199'

                Plan:Unknown, Type:Unknown

Jan  4 11:37:48.172: ISDN Se0/0/1:15 Q931: RX <- RELEASE_COMP pd = 8  callref = 0x800B

        Cause i = 0x8286 - Channel unacceptable

2 ACCEPTED SOLUTIONS

Accepted Solutions
Super Bronze

Gateway Configuration on CUCM v8

Hi

So this called number doesn't exist, or can't be reached from the GW.

Called Party Number i = 0xC1, '4621198'

If you are using MGCP: make sure you have an 'Inbound' Calling Search Space assigned to this circuit. If necessary, add translation patterns to that CSS to map '4621198' to your internal extensions, or just set 'significant digits' on the circuit in CCMAdmin to 4 (e.g. if your internal extension is 1198).

If using H.323 you need dial peers setting up, let us know if that's the case.

Aaron Harrison

Principal Engineer at Logicalis UK

Please rate helpful posts...

Aaron Please remember to rate helpful posts to identify useful responses, and mark 'Answered' if appropriate!
Hall of Fame Super Silver

Gateway Configuration on CUCM v8

Simply, change the MGCP port configuration to use significantDigits of 4, this way CUCM will only extend the last 4 digits which will match the DN. Also, make sure the CSS applied to that port has access to the partition assigned to the phone DN.

HTH,

Chris

11 REPLIES
Hall of Fame Super Gold

Gateway Configuration on CUCM v8

Have you leased 30 B channels, or a smaller number? Check with telco.

New Member

Gateway Configuration on CUCM v8

Hello Paolo,

I am using PRI channels....i have two E1's coming the the telco leasing 31 channels.

Green

Gateway Configuration on CUCM v8

Hi,

You are trying to use channel 31

Your SP is clearing the call saying that this channel (31) does not fit.

Are you sure you have all 30 channels from the SP.

Regards

Alex

Regards, Alex. Please rate useful posts.
New Member

Gateway Configuration on CUCM v8

Hello acampbell,

i have leased two E1's from the SP with service number 4621100-99. The SP are claiming they are giving all 30 channels

Hall of Fame Super Gold

Gateway Configuration on CUCM v8

So complain to telco and show them the trace you took.

They will say that all is good on their side, to which you should reply inviting them on your premises, and place a test call on channel 31 using their own test equiopment. Make sure you observe the results with your own eyes when they do that.

New Member

Gateway Configuration on CUCM v8

will get back to the telco and see how we can resolve the issue.....

will also get back to u with there update

thanks

New Member

Gateway Configuration on CUCM v8

hello guys...

Happy new year.

I was able to contact the telco and finally calls can go out.....but i have a little problem which is i can't get incoming calls but the call reaches my router. Below is the output of the debug when i place an incoming call from my GSM

Jan 18 12:18:27.835: ISDN Se0/0/1:15 Q931: RX <- SETUP pd = 8  callref = 0x0034

        Sending Complete

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA9839F

                Exclusive, Channel 31

        Calling Party Number i = 0x0083, '08030718911'

                Plan:Unknown, Type:Unknown

        Called Party Number i = 0xC1, '4621198'

                Plan:ISDN, Type:Subscriber(local)

Jan 18 12:18:27.839: ISDN Se0/0/1:15 Q931: TX -> RELEASE_COMP pd = 8  callref =

0x8034

        Cause i = 0x8081 - Unallocated/unassigned number Jan 18 12:18:27.835: ISDN Se0/0/1:15 Q931: RX <- SETUP pd = 8  callref = 0x0034
        Sending Complete
        Bearer Capability i = 0x8090A3
                Standard = CCITT
                Transfer Capability = Speech
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0xA9839F
                Exclusive, Channel 31
        Calling Party Number i = 0x0083, '08030718911'
                Plan:Unknown, Type:Unknown
        Called Party Number i = 0xC1, '4621198'
                Plan:ISDN, Type:Subscriber(local)
Jan 18 12:18:27.839: ISDN Se0/0/1:15 Q931: TX -> RELEASE_COMP pd = 8  callref =
0x8034
        Cause i = 0x8081 - Unallocated/unassigned number

Any help.

Thanks

Murtala

Super Bronze

Gateway Configuration on CUCM v8

Hi

So this called number doesn't exist, or can't be reached from the GW.

Called Party Number i = 0xC1, '4621198'

If you are using MGCP: make sure you have an 'Inbound' Calling Search Space assigned to this circuit. If necessary, add translation patterns to that CSS to map '4621198' to your internal extensions, or just set 'significant digits' on the circuit in CCMAdmin to 4 (e.g. if your internal extension is 1198).

If using H.323 you need dial peers setting up, let us know if that's the case.

Aaron Harrison

Principal Engineer at Logicalis UK

Please rate helpful posts...

Aaron Please remember to rate helpful posts to identify useful responses, and mark 'Answered' if appropriate!
New Member

Gateway Configuration on CUCM v8

Hi aaronharrison,

I am using MGCP and i have 3 CSS which are assigned to different phones.I am using CUCM 8.0.3 and i cant find significant digit" under the CCMAdmin page. The PSTN number is 46211xx and the extension is 1198.

Do i need to create another CSS for inbound.

Hall of Fame Super Silver

Gateway Configuration on CUCM v8

Simply, change the MGCP port configuration to use significantDigits of 4, this way CUCM will only extend the last 4 digits which will match the DN. Also, make sure the CSS applied to that port has access to the partition assigned to the phone DN.

HTH,

Chris

New Member

Gateway Configuration on CUCM v8

Thanks guys...

After changing the significant digit it started working.

501
Views
0
Helpful
11
Replies
CreatePlease login to create content