Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

Getting a CME 7.1 site phones to use central CM 4.2 directory

We just deployed CME 7.1 at a remote loc. I need the CME phone to look at the central CM directory. I have entered in telephony-service configuration:

url directories http://x.x.x.x:8080/CiscoWebs/IPPhoneservices/CCMIP/xmldirectory.asp

no create cnf

create cnf

reset the phones and "Host not found"

I have read that you need to enter the CME phones in the CM as well but don't understand how to get phones registered to the CME router and CM 4.2 server at the same time.

Any assistance would be appreciated.

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Red

Re: Getting a CME 7.1 site phones to use central CM 4.2 director

Hi Johnny,

The phones will not actually register with CCM 4.2 :) Also check the url, it doesn't seem right for a 4.x CCM version;

To enable an external directory resource on supported Cisco Unified IP phones and disable local directory services on those same phones, perform the following steps.

Prerequisites

To use a Cisco Unified Communications Manager directory as an external directory source for Cisco Unified CME phones, the Cisco Unified Communications Manager must be made aware of the phones. You must list the MAC addresses of the Cisco Unified CME phones in the Cisco Unified Communications Manager and reset the phones from the Cisco Unified Communications Manager. It is not necessary for you to assign ephone-dns to the phones or for the phones to register with Cisco Unified Communications Manager.

Restrictions

Provisioning of the directory URL to select an external directory resource disables the Cisco Unified CME local directory service.

SUMMARY STEPS

1. enable

2. configure terminal

3. telephony -service

4. url {directory | service} url ***something like http://172.16.242.240/CCMCIP/xmldirectory.asp

5. end

From this good CME doc;

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmedirs.html#wp1015876

Hope this helps!

Rob

2 REPLIES
Hall of Fame Super Red

Re: Getting a CME 7.1 site phones to use central CM 4.2 director

Hi Johnny,

The phones will not actually register with CCM 4.2 :) Also check the url, it doesn't seem right for a 4.x CCM version;

To enable an external directory resource on supported Cisco Unified IP phones and disable local directory services on those same phones, perform the following steps.

Prerequisites

To use a Cisco Unified Communications Manager directory as an external directory source for Cisco Unified CME phones, the Cisco Unified Communications Manager must be made aware of the phones. You must list the MAC addresses of the Cisco Unified CME phones in the Cisco Unified Communications Manager and reset the phones from the Cisco Unified Communications Manager. It is not necessary for you to assign ephone-dns to the phones or for the phones to register with Cisco Unified Communications Manager.

Restrictions

Provisioning of the directory URL to select an external directory resource disables the Cisco Unified CME local directory service.

SUMMARY STEPS

1. enable

2. configure terminal

3. telephony -service

4. url {directory | service} url ***something like http://172.16.242.240/CCMCIP/xmldirectory.asp

5. end

From this good CME doc;

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmedirs.html#wp1015876

Hope this helps!

Rob

New Member

Re: Getting a CME 7.1 site phones to use central CM 4.2 director

Yep, figured it out. The URL provided is the one. I looked in the Enterprise parameters of the CM box and matched the CME URL entry to that. I then added all the CME phones to the CM as well. It is working. Thanks!

207
Views
0
Helpful
2
Replies
CreatePlease to create content