Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

h.323 gw& Invalid number format

Hello!

i have cisco2911 with 151-4.M3 IOS, gateway configured as h.323 gw on Cisco CUCM.

when i made outside call to PSTN from IP phone i got message

Invalid number format

after

TX -> INFORMATION which gw send to PSTN

Aug 14 05:31:25.359: ISDN  Se0/0/0:15 Q931: Sending SETUP  callref = 0x00F4 callID = 0x8077 switch =  primary-net5 interface = User

Aug 14 05:31:25.359: ISDN  Se0/0/0:15 Q931: TX -> SETUP pd = 8  callref = 0x00F4

        Bearer Capability  i = 0x8090A3

                Standard  = CCITT

                Transfer  Capability = Speech

                Transfer  Mode = Circuit

                Transfer  Rate = 64 kbit/s

        Channel ID i =  0xA9838A

                 Exclusive, Channel 10

        Progress Ind i = 0x8183 - Origination address is  non-ISDN

        Calling Party  Number i = 0x2181, '8xxx420494'

                 Plan:ISDN, Type:National

        Called Party  Number i = 0xA1, '8xxx3815299'

                 Plan:ISDN, Type:National

Aug 14 05:31:25.379: ISDN  Se0/0/0:15 Q931: RX <- SETUP_ACK pd = 8  callref = 0x80F4

        Channel ID i =  0xA9838A

                 Exclusive, Channel 10

Aug 14 05:31:25.379: ISDN  Se0/0/0:15 Q931: RX <- CALL_PROC pd = 8  callref = 0x80F4

        Progress Ind i = 0x8288 - In-band info or appropriate  now available

Aug 14 05:31:28.959: ISDN  Se0/0/0:15 Q931: RX <- ALERTING pd = 8  callref =  0x80F4

Aug 14  05:31:35.359: ISDN Se0/0/0:15 Q931: TX -> INFORMATION pd = 8  callref =  0x00F4

         Sending Complete

Aug 14 05:31:35.371: ISDN  Se0/0/0:15 Q931: RX <- DISCONNECT pd = 8  callref = 0x80F4

       Cause i = 0x829C  - Invalid number format (incomplete number)

         Progress Ind i = 0x8288 - In-band info or appropriate  now available 

         Display i = 'WRONG NUMBER '

But if i push button "Redial" on IP phone call go with out problem and i don't see message

Aug 14  05:31:35.359: ISDN Se0/0/0:15 Q931: TX -> INFORMATION pd = 8  callref =  0x00F4

          Sending Complete

Aug 14 05:32:01.838: ISDN  Se0/0/0:15 Q931: Sending SETUP  callref = 0x00F5 callID = 0x8078 switch =  primary-net5 interface = User

Aug 14 05:32:01.838: ISDN  Se0/0/0:15 Q931: TX -> SETUP pd = 8  callref = 0x00F5

        Bearer Capability  i = 0x8090A3

                Standard  = CCITT

                Transfer  Capability = Speech 

                Transfer  Mode = Circuit

                Transfer  Rate = 64 kbit/s

        Channel ID i =  0xA9838A

                 Exclusive, Channel 10

        Progress Ind i = 0x8183 - Origination address is  non-ISDN 

        Calling Party  Number i = 0x2181, '8xxx420494'

                 Plan:ISDN, Type:National

        Called Party  Number i = 0xA1, '8xxx3815299'

                 Plan:ISDN, Type:National

Aug 14 05:32:01.854: ISDN  Se0/0/0:15 Q931: RX <- SETUP_ACK pd = 8  callref = 0x80F5

        Channel ID i =  0xA9838A

                 Exclusive, Channel 10

Aug 14 05:32:01.858: ISDN  Se0/0/0:15 Q931: RX <- CALL_PROC pd = 8  callref = 0x80F5

        Progress Ind i = 0x8288 - In-band info or appropriate  now available

Aug 14 05:32:05.106: ISDN  Se0/0/0:15 Q931: RX <- ALERTING pd = 8  callref =  0x80F5

Aug 14 05:32:17.714: ISDN  Se0/0/0:15 Q931: RX <- DISCONNECT pd = 8  callref = 0x80F5

        Cause i = 0x8391  - User busy

        Progress Ind i = 0x8288 - In-band info or appropriate  now available 

        Display i = 'BUSY

How to get rid of INFORMATION message?

Best regards,

Mike

Everyone's tags (2)
1 REPLY
Hall of Fame Super Silver

h.323 gw& Invalid number format

Is the 8 part of the number or the prefix? Post your dial peer configuration.

Chris

748
Views
0
Helpful
1
Replies
CreatePlease to create content