Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

H323 Gateway - POTS Dial-peers

Hi There, this issue is causing me much frustration. We are running CUCM 6.1 and a 3845 ISR running advipsvcs 124-15.T8 IOS. Basically, outbound calls are not matching the specific dialpeers that I have configured on the H323 Gateway. We also have a GSM gateway on port 0/2/1 which should be routing mobile calls 69........

We have the following Route Patterns, all set to Discard Digits <none>. The route list is also configured with Discard Digits <none>:

0.14XXX

0.69XXXXXXXX

0.2XXXXXXXXX

0.80XXXXXXXX

0.00!

0.118XX

0.901!

0.11XXX

166

199

100

We have the following Dial-peers configured, but all outbound calls are matching dial-peer 2000:

dial-peer voice 2001 voip

preference 1

destination-pattern 2...

voice-class codec 1

voice-class h323 1

session target ipv4:10.129.20.3

fax rate 7200 bytes 48

fax nsf 000000

fax protocol pass-through g711ulaw

no vad

!

dial-peer voice 2002 voip

preference 2

destination-pattern 2...

voice-class codec 1

voice-class h323 1

session target ipv4:10.129.16.34

fax rate 7200 bytes 48

fax nsf 000000

fax protocol pass-through g711ulaw

no vad

!

dial-peer voice 100 pots

tone ringback alert-no-PI

description **Police**

destination-pattern 100

progress_ind setup enable 3

progress_ind progress enable 8

incoming called-number .

direct-inward-dial

port 0/2/0:15

forward-digits all

!

dial-peer voice 199 pots

tone ringback alert-no-PI

description **Fire Brigade**

destination-pattern 199

progress_ind setup enable 3

progress_ind progress enable 8

port 0/2/0:15

forward-digits all

!

dial-peer voice 166 pots

tone ringback alert-no-PI

description **First Aid**

destination-pattern 166

progress_ind setup enable 3

progress_ind progress enable 8

port 0/2/0:15

forward-digits all

!

dial-peer voice 6969 pots

tone ringback alert-no-PI

description **Mobile Calls**

preference 1

destination-pattern 0.69........

progress_ind setup enable 3

progress_ind progress enable 8

incoming called-number .

direct-inward-dial

port 0/2/1:15

!!

dial-peer voice 2004 pots

tone ringback alert-no-PI

description **Intl**

preference 1

destination-pattern 0.00T

progress_ind setup enable 3

progress_ind progress enable 8

incoming called-number .

direct-inward-dial

port 0/2/0:15

!

dial-peer voice 2005 pots

tone ringback alert-no-PI

description **Greece PSTN**

preference 1

destination-pattern 0.2.........

progress_ind setup enable 3

progress_ind progress enable 8

incoming called-number .

direct-inward-dial

port 0/2/0:15

!

dial-peer voice 2006 pots

tone ringback alert-no-PI

description **Freephone**

preference 1

destination-pattern 0.8.........

progress_ind setup enable 3

progress_ind progress enable 8

incoming called-number .

direct-inward-dial

port 0/2/0:15

!

dial-peer voice 2000 pots

tone ringback alert-no-PI

preference 2

destination-pattern 0.T

progress_ind setup enable 3

progress_ind progress enable 8

incoming called-number .

direct-inward-dial

port 0/2/0:15

!

dial-peer voice 2007 pots

tone ringback alert-no-PI

description **Dir Svcs**

preference 1

destination-pattern 0.1....

progress_ind setup enable 3

progress_ind progress enable 8

incoming called-number .

direct-inward-dial

port 0/2/0:15

2 REPLIES
New Member

Re: H323 Gateway - POTS Dial-peers

Not to worry folks, resolved it after stepping back and looking at the config again...

on the pots dial-peer voice 69 I changed the destination-patter to 069........ and then did forward-digits 10. Works a treat.

New Member

Re: H323 Gateway - POTS Dial-peers

Not to worry folks, resolved it after stepping back and looking at the config again...

on the pots dial-peer voice 69 I changed the destination-patter to 069........ and then did forward-digits 10. Works a treat.

166
Views
0
Helpful
2
Replies
CreatePlease to create content