Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Help with Voice Gateway Outgoing Calls

Please Help.  I have an analog line plugged into a fxo port for our backup just in our VOIP environment.  I can make incoming calls to the analog line and it correctly forwards to the internal extension assign on the connection plar.  But when i try and make a call from the router.  I receive a disconnect.  csim start has been pretty helpful in testing my other 28 sites.

error:

csim start 94231294
csim: called number = 94231294, loop count = 1 ping count = 0

csim err csimDisconnected recvd DISC cid(54)
csim: loop = 1, failed = 1 
csim: call attempted = 1, setup failed = 1, tone failed = 0

Here's my configs:

!
voice-port 1/0/0
no comfort-noise
connection plar 1760
!
voice-port 1/0/1
no comfort-noise
connection plar 1760
!
mgcp call-agent 10.1.200.11 service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode out-of-band
!
mgcp profile default
!
!
!
dial-peer cor custom
!
!
!
dial-peer voice 100 pots
destination-pattern 9T
port 1/0/0
!        
dial-peer voice 101 pots
preference 1
destination-pattern 9T
port 1/0/1
!        
dial-peer voice 911100 pots
destination-pattern 911
port 1/0/0
prefix 911
!        
dial-peer voice 911101 pots
preference 1
destination-pattern 911
port 1/0/1
prefix 911
!        
dial-peer voice 2000 voip
destination-pattern [1-8]...
session target ipv4:10.1.200.11
no vad  
!        
dial-peer voice 2001 voip
preference 1
destination-pattern [1-8]...
session target ipv4:10.1.200.10
no vad  
!        
dial-peer voice 9000 voip
destination-pattern 9T
session target ipv4:10.1.200.11
!        
dial-peer voice 9001 voip
preference 1
destination-pattern 9T
session target ipv4:10.1.200.10
no vad  
!        
dial-peer voice 7100 pots
destination-pattern 9[2-9]......
port 1/0/0
!        
dial-peer voice 7101 pots
preference 1
destination-pattern 9[2-9]......
port 1/0/1
!        
dial-peer voice 10100 pots
destination-pattern 91[2-9].........
port 1/0/0
!        
dial-peer voice 10101 pots
preference 1
destination-pattern 91[2-9].........
port 1/0/1
!        
!        
call-manager-fallback
max-conferences 4
ip source-address 192.168.73.1 port 2000
max-ephones 48
max-dn 96

Any help would be greatly appreciated.  Thanks!

4 REPLIES

Re: Help with Voice Gateway Outgoing Calls

Did u tried calling with IP Phones or with testing with csim only? Did u configured proper route patterns at CUCM?

I can see it's your MGCP gateway but didn't configured the voice-ports and dial-peers correctly according to MGCP configurations, you can have a look here for MGCP configurations:

http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note09186a008017825e.shtml

HTH

New Member

Re: Help with Voice Gateway Outgoing Calls

Yes I only tried testing using CSIM... I very new to the voice side.  I will read over the document you sent in the link.  And let you know.  Thanks!

Silver

Re: Help with Voice Gateway Outgoing Calls

too many unknowns for a definitive answer here

-

You are running CCM?  What version (just for kicks and giggles)?

you have bits of MGCP and H323 - what do you want to run here?

You are catching the incoming calls with H323 dial-peers

Have you connected a buttset or normal analog phone to the FXO to check dial out?  Some CO trunks do not provide dial-tone ( a human oriented signalling method) - you can still diall out as long as there is battery

Can you do a debug voice dialpeer to see which dialpeer you are matching outbound?

Also try a debug vpm signaling to see what is actually happening

Dial-peers 9000 and 9001 are also competeing with 100 and 101 - what are you trying to accomplish?

When you attempt to make a call "from the router" is only via CSIM?

New Member

Re: Help with Voice Gateway Outgoing Calls

Hello,

Sorry for little information.  I am very new to the voice side of the router configs.  I really don't have a lot of answers for you because I didn't configure the voice stuff, so I don't what the purposes of some of the features that is in the config.  I only tested using CSIM.  I will do some of the debug option you listed.  Thanks!

900
Views
0
Helpful
4
Replies