Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

How to add a couple new DID ranges into voice gateway

So we ran out of DID's in our current range. We ordered some new ones and we will get the via our telco tomorrow. It seems they add them to the PRI on there side. My question is how do I get them into our cisico voip setup to work for our users? we are going from a 55xx range to adding a 89XX and 44XX range.

We are running cucm 8.6 and have a Cisco R2901 switch.

13 REPLIES
Cisco Employee

How to add a couple new DID ranges into voice gateway

If using H323/SIP, add the dial peers to match those DIDs and send calls to CUCM

Also make sure the inbound CSS is correct in CUCM

For MGCP, just adjust the inbound CSS

Then you can start using those DIDs within CUCM

HTH

java

if this helps, please rate

www.cisco.com/go/pdihelpdesk

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
New Member

How to add a couple new DID ranges into voice gateway

Thanks for the quick response. Is there a guide for me to do each of these parts? We are using H323 as far as I know.

Cisco Employee

How to add a couple new DID ranges into voice gateway

No, no guides. There are config guides for each bit, but they assume you know how to tie them together.

You can look at your current config for the DPs and just copy them, adjust the destination pattern as required

You might have one DP with 55.., add one with 89.. and another one with 44..

Those are just examples, adjust as necessary, if you happen to have one with ...., then it would work with all the other DID ranges.

For the inbound CSS from CUCM, you need to know whether it requires adjustment, or not. Based on your dial plan.

HTH

java

if this helps, please rate

www.cisco.com/go/pdihelpdesk

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
New Member

How to add a couple new DID ranges into voice gateway

By DP you mean device pool? Is that under system -> device pool? Or do you mean Device Profile Configuration? That is specific tot he user though isint it? There is no range to add the new DID's into.

Cisco Employee

How to add a couple new DID ranges into voice gateway

Dial-peer, in the GW. You should ask your voice network admin to do this.

HTH

java

if this helps, please rate

www.cisco.com/go/pdihelpdesk

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
New Member

How to add a couple new DID ranges into voice gateway

unfortunatly that will be me on this project. We are a small company. So all the work will be done on the voice gateway it seems?

Cisco Employee

How to add a couple new DID ranges into voice gateway

Assuming your inbound CSS in CUCM is correct, yes.

HTH

java

if this helps, please rate

www.cisco.com/go/pdihelpdesk

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
New Member

Re: How to add a couple new DID ranges into voice gateway

dial-peer voice 10 voip

destination-pattern 5..$

session target ipv4:10.0.1.100

dtmf-relay h245-alphanumeric

codec g711ulaw

no vad

!           

dial-peer voice 11 voip

destination-pattern 7149105[57]..$

session target ipv4:10.0.1.100

dtmf-relay h245-alphanumeric

codec g711ulaw

no vad

!

dial-peer voice 12 voip

destination-pattern 71491057..$

session target ipv4:10.0.1.100

dtmf-relay h245-alphanumeric

codec g711ulaw

no vad

So basically I can use the references above and just create a dial-peer voice 13 and 14? and change the pattern?

Cisco Employee

How to add a couple new DID ranges into voice gateway

Yes, no idea why you have all those DPs, I assume 10.0.1.100 is your CUCM.

You usually just match the number of digits telco will send at all times, and not have a 10 digit DP and 3 digit DP at the same time.

Also, 11 does almost the same thing as 12, it matches 5 or 7, when you already have one to match 7???

I have no idea why you have this, and how it works in your system without looking at all your config.

Call telco, ask them how many digits they will be sending for those DIDs.

Then adjust the destination pattern from this one as necessary.

dial-peer voice 10 voip

destination-pattern 5..$

session target ipv4:10.0.1.100

dtmf-relay h245-alphanumeric

codec g711ulaw

no vad

Change the DP number to something that does not exists already.

HTH

java

if this helps, please rate

www.cisco.com/go/pdihelpdesk

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
New Member

How to add a couple new DID ranges into voice gateway

I cannot speak for why they are setup that way. I didnt create them. So you think I should use dial plan 10 as the example to file? I know our carrier is sending 10 digits.

So would it look something like

dial-peer voice 13 voip

destination-pattern 4..$

session target ipv4:10.0.1.100

dtmf-relay h245-alphanumeric

codec g711ulaw

no vad

!

dial-peer voice 14 voip

destination-pattern 8..$

session target ipv4:10.0.1.100

dtmf-relay h245-alphanumeric

codec g711ulaw

no vad

Or would I be better off using the others?

dial-peer voice 13 voip

destination-pattern 71485089..$

session target ipv4:10.0.1.100

dtmf-relay h245-alphanumeric

codec g711ulaw

no vad

!

dial-peer voice 14 voip

destination-pattern 71485044..$

session target ipv4:10.0.1.100

dtmf-relay h245-alphanumeric

codec g711ulaw

no vad

Cisco Employee

How to add a couple new DID ranges into voice gateway

If you expect 10 digits, then you need to use the latter ones, that will match 10 digits.

HTH

java

if this helps, please rate

www.cisco.com/go/pdihelpdesk

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
New Member

How to add a couple new DID ranges into voice gateway

Gotcha. Thanks for the help. Is there anything I should check in CUCM to make sure is matching? or will the GW changes be all that i need to do?

New Member

Re: How to add a couple new DID ranges into voice gateway

Jaime. Are you good with the voice gateway? below is the last 4 digits to the ranges I am adding. the first 3 digits are the same on all the ranges of 754. Currently the rules are as above. Is there a blanket config I can do for either all the ranges below. or do I need to create 3?

4300 to 4499

8960 to 8979

For example will

destination-pattern 714457....$

work for the whole range of 457? Or am i better off breaking up the DID's in chunks of 100?

1776
Views
0
Helpful
13
Replies
CreatePlease login to create content