Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

How to change Administrator Username (OS/Diaster/CLI) in CUCM - 9.1.2

Dears - Can anyone help me with command to change Administrator Username (OS/Diaster/CLI) in CUCM - 9.1.2.

I can see command to change Administrator Passoword (OS/Diaster/CLI) not the username.

Thanks,

Siva

SIVANESAN R
18 REPLIES
New Member

Hello Siva,please find this

Hello Siva,

please find this link:

http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/cli_ref/9_1_1/CUCM_BK_C6AE17AA_00_cucm-cli-reference-guide-91/CUCM_BK_C6AE17AA_00_cucm-cli-reference-guide-91_chapter_0110.html#CUCM_CL_SB2BA64F_00

you can create a new user and give him the admin privilege.

I don't think the the OS password can be changed.

Regards,

Mohamed Helmy

Regards, Mohamed Helmy
New Member

 Hi I have the same question

 

Hi I have the same question but in Call Manager 8.6.2... I tried to search by Internet and other forums, papers, etc..  and I did not get nothing clear. I think that Administrator Username (OS admin/Disaster/CLI) can not  be change by us. Probably Cisco TAC in the root or something that, I don´t know. My last question if I create a new account with privilege 1 (advanced), this account can do the same in (OS admin/Disaster/CLI) that account created at the start of installation?  this account or username regarding command "show account" has privilege 4...  please somebody feedback to us about it?.... thanks a lot..

VIP Purple

Hi, what best u can do is

Hi,

 

what best u can do is create another with  set account name command ?

 

regds,

aman

See the installation guide.

See the installation guide. Table 2 under the "Server Installation Information" section.

 

http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/install/9_1_1/CUCM_BK_I05CD008_00_installing-cucm-91/CUCM_BK_I05CD008_00_installing-cucm-91_chapter_01.html#CUCM_RF_ID154C37_00

 

Parameter

Description

Can Entry Be Changed After Installation?

Administrator ID

This field specifies the administrator account user ID that you use for secure shell access to the CLI, for logging into Cisco Unified Communications Operating System Administration and for logging into theDisaster Recovery System.

No, you cannot change the entry after installation.

Note   

After installation, you can create additional administrator accounts, but you cannot change the original administrator account user ID.

Basically, you cannot change the OS/platform administrator ID after install. You can change the password (as you have already found). 

 

HTH

 

-Bill (@ucguerrilla)

 

HTH -Bill (b) http://ucguerrilla.com (t) @ucguerrilla

Please remember to rate helpful responses and identify

VIP Purple

Hi Bill ,thanks for sharing

Hi Bill ,

thanks for sharing info.[+5]

 

regds,

aman

Thanks Bill 

Thanks Bill 

SIVANESAN R
New Member

Sorry if this was answered,

Sorry if this was answered, but I didnt see it;  how do you add an Admin account to log into OS Administration/Disaster Recovery/etc? 

 

Is there any way to assign a regular end user with the rights for this?  I believe not.  Im also assuming I should NOT make my new OS admin name the same as an end user's name?

New Member

Hello William ,

Hello William ,

I appreciate if you could answer the following questions:

1. we are using administration account to log in to the GUI of CuCM ,...and  we have few people using same credential to log in to the GUI. We are planning to create a user name for each person with same privilege as administration account. How we can do that?

2.Does it work in version 7 and below ?  

Cisco Employee

Give the Standard CCM Admin

Give the Standard CCM Admin Users role to give them access to CUCM admin page. Complete details about various other roles and groups available in CUCM can be found in below document:

http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/admin/8_0_2/ccmsys/accm-802-cm/a02mla.html&ei=z-TotCjv&lc=en-IN&s=1&m=466&ts=1451488857&sig=ALL1Aj4fYhLVHuGZlAVezRYS0vlv9tuZnQ

Regards

Deepak

- Rate Helpful Posts -

New Member

Thanks.

Thanks.

404 Page Not Found

Can not open the page.

Does it work in version 7 and below ? 

New Member

Thanks.Can not open the page.

Thanks.Can not open the page.

Can we create local userID in Version 7 and give the Standard CCM Admin Users role to give them access to CUCM admin page ?

Cisco Employee

Yes, assuming you're not LDAP

Yes, assuming you're not LDAP integrated, in anything below CUCM 9.x it's either ALL local users, or ALL LDAP users, not both at the same time.

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
New Member

What about Unity Connections

What about Unity Connections and UCCX ? can we apply same concept for both?

New Member

yes. for Unity u just need to

yes. for Unity u just need to give system administrator or technician roles in the user. Uccx is similar add admin or other to user account. 

Cisco Employee

A user with only the Standard

A user with only the Standard CCM Admin Users role can access Cisco Unified Communications Manager Administration but cannot make any changes. A user with only the Standard CCMADMIN Administration role can make changes, but cannot authenticate entry to Cisco Unified Communications Manager Administration.

A user, therefore, must have the Standard CCM Admin Users role to access Cisco Unified Communications Manager Administration and must have at least one other role to administer the system. Hence make sure you are giving both these roles to the end user.

Find the link again, it was broken last time for some reasons. The definition of roles and groups mentioned in this document stands true for CM v7 as well.

http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/admin/8_0_2/ccmsys/accm-802-cm/a02mla.html

Regards

Deepak

New Member

Thanks

Thanks

The link still not available

Cisco Employee

Not sure why, opens fine on

Not sure why, opens fine on my side. Do Google and look for Cisco Unified Communications Manager System Guide, Release 8.0(2)

Regards

Deepak

New Member

What about Unity Connections

What about Unity Connections and UCCX ? can we apply same concept for both?

10548
Views
39
Helpful
18
Replies
CreatePlease login to create content