Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

How to Check CME license in CLI

Hi,

I need to verify my CME phone and User license in my 2851 router is there any option to find it.(Used and Unused license)

Thanks,

Hari

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Gold

Re: How to Check CME license in CLI

Up to maximum, check:

http://www.cisco.com/en/US/products/sw/voicesw/ps4625/products_device_support_tables_list.html

Please remember to rate useful posts with the scrollbox below.

8 REPLIES
Hall of Fame Super Gold

Re: How to Check CME license in CLI

There is no license enforcement or installation in CME so there is nothing to verify.

New Member

Re: How to Check CME license in CLI

So that means we can add as many phone as we want ....

Hall of Fame Super Gold

Re: How to Check CME license in CLI

Up to maximum, check:

http://www.cisco.com/en/US/products/sw/voicesw/ps4625/products_device_support_tables_list.html

Please remember to rate useful posts with the scrollbox below.

New Member

How to Check CME license in CLI

Hi,

Cisco Router is sold like below;

If CCME FL for 25 users is sold. How can   we veriyfing this situation;

http://www.cisco.com/web/partners/downloads/partner/WWChannels/technology/ipc/downloads/ucme_8_5_ue_8_5_ucc_og.pdf

Base router, 128 MB flash, 256 MB DRAM,

DSP-32, AIM2-CUE, CCME FL for 25

users, CUE FL for 25 users, 25 phone

device licenses, Cisco IOS Advanced IP

Services, 5 UCC desktop client licenses

Hall of Fame Super Red

How to Check CME license in CLI

Hi Mehmet,

In the licensing scheme, the cme-srst feature license is a "paper"

RTU (right to use) license only. There is nothing to load on the router

itself

Use the "show license" command to get started;

Activating CME-SRST Feature License


The ISR-G2 comes with a 60-day evaluation license. After 60 days, the license changes to “right to use”.
The customer is required to pay for the CME-SRST feature license which is valid for 12 years.
Prerequisites
• UCK9 license
• ISR-G2 already accepts UC CLIs


SUMMARY STEPS
1. show license detail cme-srst
2. configure terminal
3. license accept end user agreement
4. exit
5. show license detail cme-srst
6. write mem


DETAILED STEPS
Command or Action Purpose


Step 1 show license detail cme-srst
Example:
Router# show license detail cme-srst
Displays the available cme-srst license. EULA should be in NOT
ACCEPTED state.


Step 2 configure terminal
Example:
Router# configure terminal
Enters global configuration mode.


Step 3 license accept end user agreement
Example:
Router(config)# license accept end user
agreement
Configures a one-time acceptance of the EULA for cme-srst
license.
Accepts EULA by typing YES.

Step 4 exit
Example:
Router(config)# exit
Exits global configuration mode.


Step 5 show license detail cme-srst
Example:
Router# show license detail cme-srs
Displays the available cme-srst license. EULA should be in
ACCEPTED state.


Step 6 write mem
Example:
Router# write mem
Saves configuration.
Command or Action

This is explained in more detail starting on Page 15;

http://www.cisco.com/en/US/docs/routers/access/sw_activation/SA_on_ISR.pdf

Cheers!

Rob

Hall of Fame Super Gold

Re: How to Check CME license in CLI

I see that someone has low-rated Rob's answer above that is, of course, 100% correct and complete. That is not fair.

To partially compensate, I have rated it again: +5.

New Member

How to Check CME license in CLI

OK

Thanks for you help.

Blue

How to Check CME license in CLI

Hi

As said earlier , CME-SRST licenses are paper license and will not be seen in the sh run or any out put of the router.

Customer has to keep in mind and remember what they have purchsed from Cisco.

Regards

Ronak patel

Regards Ronak Patel Rate all helpful post by clicking stars below the answer.
7081
Views
32
Helpful
8
Replies
CreatePlease to create content