Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 

how to clear the hung calls in CUBE?

I'm installing a new CUBE as SIP-SIP gateway in Cisco 2921, IOS: 15.1(4)M3. When i tried few test calls, I saw couple of hung calls in it.

I tried clearing them manually with the below command but it didn't help.

clear call voice causecode identifier{id identifier | media-inactive | calling-number number | called-number number}

>> https://supportforums.cisco.com/docs/DOC-34379

The call legs are still in connecting status.

2    : 2152 13:36:28.319 CET Tue Feb 11 2014.1 +-1 pid:200 Answer 222022029 connecting

dur 00:00:00 tx:0/0 rx:0/0

IP X.X.X.97:24578 SRTP: off rtt:0ms pl:0/0ms lost:0/0/0 delay:0/0/0ms g711ulaw TextRelay: off

media inactive detected:n media contrl rcvd:n/a timestamp:n/a

long duration call detected:n long duration call duration:n/a timestamp:n/a

2    : 2157 13:38:54.589 CET Tue Feb 11 2014.1 +-1 pid:200 Answer 222022029 connecting

dur 00:00:00 tx:0/0 rx:0/0

IP X.X.X.97:24582 SRTP: off rtt:0ms pl:0/0ms lost:0/0/0 delay:0/0/0ms g711ulaw TextRelay: off

media inactive detected:n media contrl rcvd:n/a timestamp:n/a

long duration call detected:n long duration call duration:n/a timestamp:n/a

Also, I tried enabling media inactivity timer but it would clear only the calls in 'Connected' status If I understand correctly.

how to clear those hung calls? and what could be the cause of it?

Any help would be much appreciated.

Thanks in advance

Suresh

//Suresh Please rate all the useful posts.
8 REPLIES

Re:how to clear the hung calls in CUBE?

Hi Suresh,


Step no 6 in the following link:

The Media Inactivity Timer enables the Active/Standby router pair to monitor and disconnect calls if no Real-Time Protocol (RTP) packets are received within a configurable time period.

When RTP packets for a call are not received by the Active/Standby router, the SIP Media Inactivity Timer releases the session. This is used to guard against any hung sessions that might have resulted from the failover in the event that a normal call disconnect does not clear the call.

The same duration for the Media Inactivity Timer should be configured on both routers. The default value is 28 seconds. This timer is configured as follows:

ip rtcp report interval 3000 gateway media-inactivity-criteria all timer receive-rtp 86400 timer receive-rtcp 5




http://www.cisco.com/c/en/us/support/docs/voice-unified-communications/unified-border-element/112095-cube-hsrp-config-00.html#step6

Kindly rate the post accordingly.

Sent from Cisco Technical Support Android App

how to clear the hung calls in CUBE?

Hi Kevin,

Yes I did try that feature but no luck, the calls are not yet cleared. but I enabled that feature after I saw the call hanging. and when I executed 'show call active voice brief' I still see 'media inactivity detected=No'.

//Suresh Please rate all the useful posts.
VIP Super Bronze

Re:how to clear the hung calls in CUBE?

Suresh have you tried this:

ip rtcp report interval 5000

gateway

timer media-inactive 5

The challenge you may face is that the media inactivity was not configured before this call started, hence it cant activate the time for this particular call...

Give it a go, lets know if it works. Even if it doesnt I suggest you enable this on your CUBE going forward, so you dont haver hung calls in the future

example: You can use the debug ccsip events to see the media inactivity timer kicking in for a call...

Router# debug ccsip events


00:04:29: sipSPICreateAndStartRtpTimer: Valid RTP/RTCP session found and CLI ena 

bled to create and start the inactivity timer 

00:04:29: sipSPICreateAndStartRtpTimer:Media Inactivity timer created for call. 

Mfactor(from CLI): 5 RTCP bandwidth: 500 

RTCP Interval(in ms): 5000 

Normalized RTCP interval (in ms):25000 

Please rate all useful posts

"The essence of christianity is not the enthronement but the obliteration of self --William Barclay"

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"

how to clear the hung calls in CUBE?

Hello Deji,

As I enabled the inactivity timer after the calls, it seems they are not detecting and clearing those hung calls.

I tried the below

      ip rtcp report interval 9000

      gateway

      media-inactivity-criteria rtcp

      timer receive-rtcp 5

Also, I'm just wondering what could be the cause for these sessions hanging? could it be the IOS or configurations or Provider side? any idea?

Please rate all the useful posts

//Suresh Please rate all the useful posts.
VIP Super Bronze

how to clear the hung calls in CUBE?

I have seen them on our CUBE(s) too and I honestly dont know why. It may be IOS related. This is why its good prractice to have media inactivity configured. Its not something to worry about though.

Please rate all useful posts

"The essence of christianity is not the enthronement but the obliteration of self --William Barclay"

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"

how to clear the hung calls in CUBE?

one of my friends from tac said, only reboot would clear those calls. did the reboot and the hung calls were cleared.

thanks everyone for your suggestions.

Please rate all the useful posts

//Suresh Please rate all the useful posts.

how to clear the hung calls in CUBE?

Suresh,

The basic thing would be resseting the TRUNK or the  "clear call voice causecode 17 called-number 2126315001"

. This to be honest looks like a IOS based issue.

Could you let us know whats the ios your running?

Regards,

Kevin

how to clear the hung calls in CUBE?

Kevin, it's Cisco 2921, IOS: 15.1(4)M3

//Suresh Please rate all the useful posts.
1229
Views
5
Helpful
8
Replies
CreatePlease to create content