Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

how to configure conference station 7936

Dear All,

I am using CME 4.2. I want to configure conference station 7936. Any pdf or sample configuration will be be very helpful.

Thanks,

Malik.

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Red

Re: how to configure conference station 7936

Hi Malik,

Are you using the "copy" command as shown in the example below;

The reason for this error message is that the archive command is for the .tar files and cannot be used with .bin files. In order to upgrade using the .bin file, use the copy command.

Router# copy tftp://x.x.x.x/P00307020300.sbn flash:

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmeinstl.html#wp998282

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmeinstl.html#wp1070512

Hope this helps!

Rob

8 REPLIES
Bronze

Re: how to configure conference station 7936

New Member

Re: how to configure conference station 7936

hi MK,

Can you tell me how it will register with my CME Router...because its showing configuring IP on the screen of the conference station...

Awaiting your reply,

Thanks,

Malik...

Bronze

Re: how to configure conference station 7936

Hi Malik, what CCME version do you have, to register a the conference station:

1. Are you using vlans and DHCP or static IP configuration?

2. Make sure that you have the firmware file on your router flash.

CME(config)#tftp-server flash:filename

3.Associate yout phone with a firmware unter telephony-service config.

- load 7936 firmware-file

4. Create an ephone-dn TAG with a number

5. Create an ephone with the MAC ephone and assiciate the button with the number

ephone 10

mac XXXX.XXXX.XXXX

button 1:DN-TAG

6. Configure your phone 7936 eith the correct IP parameters and it shoukd register with out problems

Hope this help

David

New Member

Re: how to configure conference station 7936

Hi David,

Please have a look at attached configuration of my CME 4.2...Please advice how i can configure my 7936..

Bronze

Re: how to configure conference station 7936

Hi, make sure that the firmware file is in yout router flash.

cmterm_7936.3-3-5-0.bin

Allow tftp function for this file:

tftp-server flash:cmterm_7936.3-3-5-0.bin

Under telephony sevices:

load 7936 cmterm_7936.3-3-5-0 (without extension)

Create the ephone-dn and ephone

ephone-dn 100 dual-line

description PHONE-7936

number XXXX

ephone 88

mac-address XXXX.XXXX.XXXX

button 1:100

type 7936

Hope this help

David

New Member

Re: how to configure conference station 7936

Dear David,

Thanks for your reply. One of the best and accurate reply ever seen in NetPro disccusion forms.

Dear David while uploading the firmware file in my router flash it gives this error:

%Tar checksum error in tftp://192.168.0.73/cmterm_7936.3-3-5-0.bin

Can you please help me resolving this issue. I will be very thankful to you.

Thanks & Regards,

Malik.

Hall of Fame Super Red

Re: how to configure conference station 7936

Hi Malik,

Are you using the "copy" command as shown in the example below;

The reason for this error message is that the archive command is for the .tar files and cannot be used with .bin files. In order to upgrade using the .bin file, use the copy command.

Router# copy tftp://x.x.x.x/P00307020300.sbn flash:

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmeinstl.html#wp998282

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmeinstl.html#wp1070512

Hope this helps!

Rob

New Member

Re: how to configure conference station 7936

Thanks Rob,

u rock...copy command works...thanks for the reply...

Regards,

Malik.

691
Views
15
Helpful
8
Replies
CreatePlease to create content