Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

how to disable DSP c5510 [FIXED]

Hi Experts, I need to disable a single DSP on a 2811 router.

 

C2811_CC#show voice dsp detailed 
 
DSP  DSP             DSPWARE CURR  BOOT                         PAK     TX/RX
TYPE NUM CH CODEC    VERSION STATE STATE   RST AI VOICEPORT TS ABORT  PACK COUNT
==== === == ======== ======= ===== ======= === == ========= == ===== ============
 
----------------------------FLEX VOICE CARD 0 ------------------------------
                           *DSP VOICE CHANNELS*

CURR STATE : (busy)inuse (b-out)busy out (bpend)busyout pending 
LEGEND     : (bad)bad    (shut)shutdown  (dpend)download pending

DSP   DSP              DSPWARE CURR  BOOT                         PAK   TX/RX
TYPE  NUM CH CODEC     VERSION STATE STATE   RST AI VOICEPORT TS ABRT PACK COUNT
===== === == ========= ======= ===== ======= === == ========= == ==== ============
C5510 001 01 None       24.3.4 idle  idle      0  0                 0          0/0
C5510 001 02 None       24.3.4 idle  idle      0  0                 0          0/0  !---- MUST BE DISABLED
C5510 001 03 None       24.3.4 idle  idle      0  0                 0          0/0
C5510 001 04 None       24.3.4 idle  idle      0  0                 0          0/0
C5510 001 05 None       24.3.4 idle  idle      0  0                 0          0/0

 

I tried with "test voice driver" hidden command without success.

 

Can you help me?

 

Regards.

  • IP Telephony
Everyone's tags (1)
1 ACCEPTED SOLUTION

Accepted Solutions

Hi Aman, this is the command

Hi Aman, this is the command used:

C2811_CC#test dsp device 0 1 ?
  dspware  Download flash file system DSPware.
  remove   Remove the specified DSP(s).
  reset    Reset the specified DSP(s).
  restore  Restore the specified DSP(s).

C2811_CC#test dsp device 0 1 remove 
Sep 11 16:33:30.539: flex_dsp_remove: Remove DS0 the group binding with DSP#1 first.

So I've disabled the voice-port, the controller and ds0-group/PRI interfaces before execute this command again.

And this is the result in show voice dsp detail:

BEFORE:

C2811_CC#show voice dsp detailed 
 
DSP  DSP             DSPWARE CURR  BOOT                         PAK     TX/RX
TYPE NUM CH CODEC    VERSION STATE STATE   RST AI VOICEPORT TS ABORT  PACK COUNT
==== === == ======== ======= ===== ======= === == ========= == ===== ============
 
----------------------------FLEX VOICE CARD 0 ------------------------------
                           *DSP VOICE CHANNELS*

CURR STATE : (busy)inuse (b-out)busy out (bpend)busyout pending 
LEGEND     : (bad)bad    (shut)shutdown  (dpend)download pending

DSP   DSP              DSPWARE CURR  BOOT                         PAK   TX/RX
TYPE  NUM CH CODEC     VERSION STATE STATE   RST AI VOICEPORT TS ABRT PACK COUNT
===== === == ========= ======= ===== ======= === == ========= == ==== ============
C5510 001 01 g711alaw   24.3.4 busy  idle      0  0 0/2/0:15  31    0  33143/33817
C5510 001 02 g711alaw   24.3.4 busy  idle      0  0 0/2/0:15  30    0    2680/2776
C5510 001 03 g711alaw   24.3.4 busy  idle      0  0 0/2/0:15  29    0    1328/1375
C5510 001 04 None       24.3.4 idle  idle      0  0                 0          0/0
C5510 001 05 None       24.3.4 idle  idle      0  0                 0          0/0
C5510 001 06 None       24.3.4 idle  idle      0  0                 0          0/0
C5510 001 07 None       24.3.4 idle  idle      0  0                 0          0/0
C5510 001 08 None       24.3.4 idle  idle      0  0                 0          0/0
C5510 001 09 None       24.3.4 idle  idle      0  0                 0          0/0
C5510 001 10 None       24.3.4 idle  idle      0  0                 0          0/0
C5510 001 11 None       24.3.4 idle  idle      0  0                 0          0/0
C5510 001 12 None       24.3.4 idle  idle      0  0                 0          0/0
C5510 001 13 None       24.3.4 idle  idle      0  0                 0          0/0
C5510 001 14 None       24.3.4 idle  idle      0  0                 0          0/0
C5510 001 15 None       24.3.4 idle  idle      0  0                 0          0/0
C5510 001 16 None       24.3.4 idle  idle      0  0                 0          0/0
C5510 002 01 None       24.3.4 idle  idle      0  0                 0          0/0
C5510 002 02 None       24.3.4 idle  idle      0  0                 0          0/0
C5510 002 03 None       24.3.4 idle  idle      0  0                 0          0/0
C5510 002 04 None       24.3.4 idle  idle      0  0                 0          0/0
C5510 002 05 None       24.3.4 idle  idle      0  0                 0          0/0
C5510 002 06 None       24.3.4 idle  idle      0  0                 0          0/0

 

AFTER

C2811_CC#show voice dsp detailed 
 
DSP  DSP             DSPWARE CURR  BOOT                         PAK     TX/RX
TYPE NUM CH CODEC    VERSION STATE STATE   RST AI VOICEPORT TS ABORT  PACK COUNT
==== === == ======== ======= ===== ======= === == ========= == ===== ============
 
----------------------------FLEX VOICE CARD 0 ------------------------------
                           *DSP VOICE CHANNELS*

CURR STATE : (busy)inuse (b-out)busy out (bpend)busyout pending 
LEGEND     : (bad)bad    (shut)shutdown  (dpend)download pending

DSP   DSP              DSPWARE CURR  BOOT                         PAK   TX/RX
TYPE  NUM CH CODEC     VERSION STATE STATE   RST AI VOICEPORT TS ABRT PACK COUNT
===== === == ========= ======= ===== ======= === == ========= == ==== ============
C5510 002 01 None       24.3.4 idle  idle      0  0                 0          0/0
C5510 002 02 None       24.3.4 idle  idle      0  0                 0          0/0
C5510 002 03 None       24.3.4 idle  idle      0  0                 0          0/0
C5510 002 04 None       24.3.4 idle  idle      0  0                 0          0/0
C5510 002 05 None       24.3.4 idle  idle      0  0                 0          0/0
C5510 002 06 None       24.3.4 idle  idle      0  0                 0          0/0

 

 

Simply all DSPs of the slot 0 id 1 are not present or available.
Checked also with show voice dsp group all.

Regards.

 

11 REPLIES
VIP Purple

Hi, after u run the command,

Hi,

 

after u run the command, test voice driver , do u get any output?

 

regds,

aman

Hi Aman, this is the option

Hi Aman, this is the option list of test voice driver:

 

C2811_CC#test voice driver
Enter VPM or HDV or ATM AIM or NM-HD-xx or HDV2 slot number : 0

C2800 Debugging Section;

1 - FPGA Registers Read/Write
2 - 5510 DSP test
3 - DSPRM test
4 - HDLC32 test
5 - Quit

Select option : 2

5510 DSP Testing Section:

1 - Reset ALL DSPs
2 - Reset 1 DSP
3 - Download DSPware
4 - CHPIR Enable/Disable
5 - Display c5510 ring
6 - Show HPI RAM
7 - Show eHPI memory thru Relay command
8 - Show Controller
9 - c5510 Keepalive Enable/Disable
10 - Download bootloader using indirect slave access
11 - Write HPI RAM
13 - DSP application download
14 - faked dsp crash
15 - Wait in Firmware Restart Indication
16 - Display DSP Keepalive Status
17 - QUIT

 

 

I tried also "test dsp device remove" but dsp still active

 

C2811_CC#test dsp device 0 1 ?
  dspware  Download flash file system DSPware.
  remove   Remove the specified DSP(s).
  reset    Reset the specified DSP(s).
  restore  Restore the specified DSP(s).

C2811_CC#test dsp device 0 1 remove

 

----------------------------FLEX VOICE CARD 0 ------------------------------
                           *DSP VOICE CHANNELS*

CURR STATE : (busy)inuse (b-out)busy out (bpend)busyout pending 
LEGEND     : (bad)bad    (shut)shutdown  (dpend)download pending

DSP   DSP              DSPWARE CURR  BOOT                         PAK   TX/RX
TYPE  NUM CH CODEC     VERSION STATE STATE   RST AI VOICEPORT TS ABRT PACK COUNT
===== === == ========= ======= ===== ======= === == ========= == ==== ============
C5510 001 01 g711alaw   24.3.4 busy  idle      0  0 0/2/0:15  31    0  11897/12158
C5510 001 02 g711alaw   24.3.4 busy  idle      0  0 0/2/0:15  30    0    8221/8432
C5510 001 03 None       24.3.4 idle  idle      0  0                 0          0/0
C5510 001 04 None       24.3.4 idle  idle      0  0                 0          0/0

 

Do you have a suggestion?

BR

VIP Purple

Hi BR, Did u try option 4

Hi BR,

 

Did u try option 4 CHPIR Enable/Disable after u select option 2 5510 DSP test?

 

regds,

aman

Hi Aman, the option 4 CHPIR

Hi Aman, the option 4 CHPIR Enable/Disable works like a reset, it doesn't disable the dsp:

 

C2811_CC#test voice driver
Enter VPM or HDV or ATM AIM or NM-HD-xx or HDV2 slot number : 0

C2800 Debugging Section;

1 - FPGA Registers Read/Write
2 - 5510 DSP test
3 - DSPRM test
4 - HDLC32 test
5 - Quit

Select option : 2

5510 DSP Testing Section:

1 - Reset ALL DSPs
2 - Reset 1 DSP
3 - Download DSPware
4 - CHPIR Enable/Disable
5 - Display c5510 ring
6 - Show HPI RAM
7 - Show eHPI memory thru Relay command
8 - Show Controller
9 - c5510 Keepalive Enable/Disable
10 - Download bootloader using indirect slave access
11 - Write HPI RAM
13 - DSP application download
14 - faked dsp crash
15 - Wait in Firmware Restart Indication
16 - Display DSP Keepalive Status
17 - QUIT

Select option : 4
 Enter DSP id : 1
 (1=Enable, 0=Disable)
0

5510 DSP Testing Section:

1 - Reset ALL DSPs
2 - Reset 1 DSP
3 - Download DSPware
4 - CHPIR Enable/Disable
5 - Display c5510 ring
6 - Show HPI RAM
7 - Show eHPI memory thru Relay command
8 - Show Controller
9 - c5510 Keepalive Enable/Disable
10 - Download bootloader using indirect slave access
11 - Write HPI RAM
13 - DSP application download
14 - faked dsp crash
15 - Wait in Firmware Restart Indication
16 - Display DSP Keepalive Status
17 - QUIT

Select option : 16

DSP Keepalive Status Display:
=============================
DSP 1 is Alive, State: 4, Keepalive Sent: 0, Skip 0
DSP 2 is Alive, State: 4, Keepalive Sent: 2918, Skip 2918
DSP 3 is Alive, State: 4, Keepalive Sent: 3969, Skip 3970
DSP 4 is Alive, State: 4, Keepalive Sent: 3969, Skip 3970
DSP 5 is Alive, State: 4, Keepalive Sent: 3969, Skip 3970
DSP 6 is Alive, State: 4, Keepalive Sent: 3969, Skip 3970
DSP 7 is Alive, State: 4, Keepalive Sent: 3969, Skip 3970
DSP 8 is Alive, State: 4, Keepalive Sent: 2917, Skip 2918

sh voice dsp detailed 
 
DSP  DSP             DSPWARE CURR  BOOT                         PAK     TX/RX
TYPE NUM CH CODEC    VERSION STATE STATE   RST AI VOICEPORT TS ABORT  PACK COUNT
==== === == ======== ======= ===== ======= === == ========= == ===== ============
 
----------------------------FLEX VOICE CARD 0 ------------------------------
                           *DSP VOICE CHANNELS*

CURR STATE : (busy)inuse (b-out)busy out (bpend)busyout pending 
LEGEND     : (bad)bad    (shut)shutdown  (dpend)download pending

DSP   DSP              DSPWARE CURR  BOOT                         PAK   TX/RX
TYPE  NUM CH CODEC     VERSION STATE STATE   RST AI VOICEPORT TS ABRT PACK COUNT
===== === == ========= ======= ===== ======= === == ========= == ==== ============
C5510 001 01 None       24.3.4 idle  idle      0  0                 0          0/0
C5510 001 02 None       24.3.4 idle  idle      0  0                 0          0/0
C5510 001 03 None       24.3.4 idle  idle      0  0                 0          0/0

 

Do you have other ideas?

Regards.

VIP Purple

Can you try reset after

Can you try reset after disable ?

After this , no more ideas.

Any reason why u want to disable ?

 

regds,

aman

Do you mean reload the router

Do you mean reload the router or reset the dsp?


I want disable the second dsp because every calls that use this chip has a bad audio with loud noise. Every other dsp working right.

 

Thanks.

VIP Purple

Reset DSP. regds,aman

Reset DSP.

 

regds,

aman

Hi, I found the right way.In

Hi, I found the right way.
In order to disable a C5510 dsp, we must use the command "test dsp device X Y remove" after disabling of voice-port, controller and ds0-group/PRI interfaces.

Regards.

VIP Purple

Hi , thanks for update[+5] Is

Hi ,

 

thanks for update[+5]

 

Is this hidden command?

 

Can u share the output of test dsp device command along with show voice dsp detailed?

regds,

aman

431
Views
15
Helpful
11
Replies
This widget could not be displayed.