cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
897
Views
0
Helpful
3
Replies

How to implement/distribute One DID (ISDN E1 PRI) between two CME Routers

Shahbaz
Level 1
Level 1

Hi,

I want to implement/distribute 1 DID (ISDN E1 PRI) between two Callmanager express systems.

Lets suppose I have Direct Inward Dial on Central site CME but I want to utilize/distribute half of the DID numbers/pool on the remote CME over the WAN.

How can I configure/implement this scenario? Any reference document would be of great help.

Thanks a lot.

-Muhammad

2 Accepted Solutions

Accepted Solutions

Driss BENATTOU
Level 4
Level 4

Hi,

You have to use voice translation rule for incoming calls.

When call comes In, you translate it to 1#xxxx you Apply

Num-exp 1#xxxx xxxx (for local DIDs) And Num-exp 1#xxxx 2#xxxx for remote DIDs And

Dial-peer voice 1 voir

Destination-pattern 2#xxxx

Session target ipv4:x.x.x.x

On the second CME, you have to Apply also Num-exp 2#xxxx xxxx

And ephone-dn 123 dual-Line (octobre-Line) nombre xxxx

Plz rate if its correct.

Regards

Driss

Sent from Cisco Technical Support iPad App

View solution in original post

Marwan ALshawi
VIP Alumni
VIP Alumni

Hi Muhammad,

this can be very easy or very complex and all depends on how you design your dial plan for internal nnumber

as best practice always keep it simple

lets say your DID range 012345XX ( where XX is 00 to 99 )

lets assume that 500 to 549 to be used for the local GW/CME and 550 to 599 to be used for the remote CME

also assuming that you are using 4 digit internal numbers with the above DID site code + 3 digit DID sit eone wil lbe like

1 site ID + 550 to 549

2 site ID + 551 to 599

so you need translation pattern to match incoming called number from the DID range, keep last 3 digits and to prefix the relevant site ID

example call coming to number 01234505 will be translated to 1505 and go to the local register IP phone

while a call to 01234580 will be translated to 2580 and will be sent over the WAN to CME2 and to the local registered IP phone on the remote CME with number 2580

and to send the cal lover the WAN you need a VOIP dial peer with desination aptteren as 25.. in our example

make sur eyou apply the mentioned translation to the inbound pots dial-peer to make sure the called number being translated at the first stage example for the above translation :

voice translation-rule 10

rule 1 /^\01234\(5[0-4].\)/ /1\1/

rule 1 /^\01234\(5[5-9].\)/ /2\1/

!

voice translation-profile P1

translate called 10

dial-peer voice xx pots

description *** Incomming POTS Dial-Peer ***

translation-profile incoming P1

direct-inward dial

dial-peer voice yy voip

description to remote CME

destination-pattern 25[5-9].

sesssion targetipv4:

hope this help

if helpful Rate

View solution in original post

3 Replies 3

Driss BENATTOU
Level 4
Level 4

Hi,

You have to use voice translation rule for incoming calls.

When call comes In, you translate it to 1#xxxx you Apply

Num-exp 1#xxxx xxxx (for local DIDs) And Num-exp 1#xxxx 2#xxxx for remote DIDs And

Dial-peer voice 1 voir

Destination-pattern 2#xxxx

Session target ipv4:x.x.x.x

On the second CME, you have to Apply also Num-exp 2#xxxx xxxx

And ephone-dn 123 dual-Line (octobre-Line) nombre xxxx

Plz rate if its correct.

Regards

Driss

Sent from Cisco Technical Support iPad App

Marwan ALshawi
VIP Alumni
VIP Alumni

Hi Muhammad,

this can be very easy or very complex and all depends on how you design your dial plan for internal nnumber

as best practice always keep it simple

lets say your DID range 012345XX ( where XX is 00 to 99 )

lets assume that 500 to 549 to be used for the local GW/CME and 550 to 599 to be used for the remote CME

also assuming that you are using 4 digit internal numbers with the above DID site code + 3 digit DID sit eone wil lbe like

1 site ID + 550 to 549

2 site ID + 551 to 599

so you need translation pattern to match incoming called number from the DID range, keep last 3 digits and to prefix the relevant site ID

example call coming to number 01234505 will be translated to 1505 and go to the local register IP phone

while a call to 01234580 will be translated to 2580 and will be sent over the WAN to CME2 and to the local registered IP phone on the remote CME with number 2580

and to send the cal lover the WAN you need a VOIP dial peer with desination aptteren as 25.. in our example

make sur eyou apply the mentioned translation to the inbound pots dial-peer to make sure the called number being translated at the first stage example for the above translation :

voice translation-rule 10

rule 1 /^\01234\(5[0-4].\)/ /1\1/

rule 1 /^\01234\(5[5-9].\)/ /2\1/

!

voice translation-profile P1

translate called 10

dial-peer voice xx pots

description *** Incomming POTS Dial-Peer ***

translation-profile incoming P1

direct-inward dial

dial-peer voice yy voip

description to remote CME

destination-pattern 25[5-9].

sesssion targetipv4:

hope this help

if helpful Rate

Thanks Driss & Marwan, I will try to implement this and will let you know if any further help would be required.

Marwan, can you plz explain the outbound dialing from remote CME as the DID line will be on Local CME? Thanks

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: