Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

Hunt Group and Pickup Group CCM 4.2(3)

I'm working with Cisco CCM 4.2(3) platform, configuring a Hunt Group for 5 phones; the basic feature is working fine but it need that besides this, it works together with Call Pickup Group, so in this way when a call is jumping between the phones, someone from the same group could answer it.

Is it possible to do?

Regards

fixie rider
1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Red

Re: Hunt Group and Pickup Group CCM 4.2(3)

Hi Javier,

This setup does not work without the "workaround" shown below. Once you aplly this you should be good to go :)

**Set enterprise parameter (System->Enterprise Parameters->Cisco Support Use 1) Cisco Support Use 1 to CSCsb42763 (case sensitive)

This operation added listbox (Route Plan->Route/Hunt->Hunt Pilot->hunt pilot XXXX -> Call Pickup Group) Call Pickup Group.

From this doc;

http://www.ciscotaccc.com/kaidara-advisor/voice/showcase?case=K11612191

1.- Enter

CSCsb42763 (in mixed case) in the Enterprise Parameter 'Cisco Support

Use 1' under the new group 'Cisco Support use Only' and click update. Only the value

CSCsb42763 in this parameter can enable the configuration. Change the

value to anything else to disable this functionality.

2. Go to Hunt Pilot Configuration page and select a call pickup group from the Call

Pickup Group dropdown list and click update.

CSCsb42763

Call Pickup fails on Hunt List

Issue:

Call pickup fails for hunt list when call is CFA from Route Point in 4.1(2)ES41. This is not the designed functionality for this issue and will break the Call Pickup logic.

Workaround:

Use multiple shared lines & CFNA between each shared line.

Related Bugs

Call Pickup fails when ringing line list member

Symptom: Selecting PickUp or GPickUp does not pickup the call from any of the members of a line group. Condition: CM 4.x Workaround: None. Feature not supported. Further Problem Description: Defect CSCsa66224 may appear to have allowed this feature to work in earlier versions.

Call Pickup from line group member fails after es installed

Symptom: A call is CFNA to a hunt pilot/line group. The call can no longer be picked up. Conditions: Calls CFNA to a hunt pilot. 4.1(2)ES36. Workaround: None

Hope this helps!

Rob

2 REPLIES
Hall of Fame Super Red

Re: Hunt Group and Pickup Group CCM 4.2(3)

Hi Javier,

This setup does not work without the "workaround" shown below. Once you aplly this you should be good to go :)

**Set enterprise parameter (System->Enterprise Parameters->Cisco Support Use 1) Cisco Support Use 1 to CSCsb42763 (case sensitive)

This operation added listbox (Route Plan->Route/Hunt->Hunt Pilot->hunt pilot XXXX -> Call Pickup Group) Call Pickup Group.

From this doc;

http://www.ciscotaccc.com/kaidara-advisor/voice/showcase?case=K11612191

1.- Enter

CSCsb42763 (in mixed case) in the Enterprise Parameter 'Cisco Support

Use 1' under the new group 'Cisco Support use Only' and click update. Only the value

CSCsb42763 in this parameter can enable the configuration. Change the

value to anything else to disable this functionality.

2. Go to Hunt Pilot Configuration page and select a call pickup group from the Call

Pickup Group dropdown list and click update.

CSCsb42763

Call Pickup fails on Hunt List

Issue:

Call pickup fails for hunt list when call is CFA from Route Point in 4.1(2)ES41. This is not the designed functionality for this issue and will break the Call Pickup logic.

Workaround:

Use multiple shared lines & CFNA between each shared line.

Related Bugs

Call Pickup fails when ringing line list member

Symptom: Selecting PickUp or GPickUp does not pickup the call from any of the members of a line group. Condition: CM 4.x Workaround: None. Feature not supported. Further Problem Description: Defect CSCsa66224 may appear to have allowed this feature to work in earlier versions.

Call Pickup from line group member fails after es installed

Symptom: A call is CFNA to a hunt pilot/line group. The call can no longer be picked up. Conditions: Calls CFNA to a hunt pilot. 4.1(2)ES36. Workaround: None

Hope this helps!

Rob

New Member

Re: Hunt Group and Pickup Group CCM 4.2(3)

It's works!

Thanks for your anwser

Regards

fixie rider
459
Views
0
Helpful
2
Replies
CreatePlease to create content