I can not call outside to PSTN with CME, help PLEASE!!!

wflores · ‎12-15-2006

I have a cme with 2E1s, one conected to PBX port 0/0/0 the other connected to PSTN port 0/2/0.

I can receive calls but, I can not call outside using de E1 connected to PSTN.

Here is some logs during the tests but I was not able to call outside to PSTN.

THANK VERY MUCH IN ADVANCE

CCME_LM#

*Dec 14 23:51:55.850: ISDN Se0/2/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Calling num 24133599

*Dec 14 23:51:55.850: ISDN Se0/2/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Called num 55789123

*Dec 14 23:51:55.850: ISDN Se0/2/0:15 Q931: TX -> SETUP pd = 8 callref = 0x021A

Bearer Capability i = 0x8090A3

Standard = CCITT

Transer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA9839F

Exclusive, Channel 31

Progress Ind i = 0x8183 - Origination address is non-ISDN

Calling Party Number i = 0x0183, '24133599'

Plan:ISDN, Type:Unknown

Called Party Number i = 0x81, '55789123'

Plan:ISDN, Type:Unknown

*Dec 14 23:51:55.878: ISDN Se0/2/0:15 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x821A

Cause i = 0x829F - Normal, unspecified

*Dec 14 23:51:55.882: ISDN Se0/2/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Calling num 9506

*Dec 14 23:51:55.882: ISDN Se0/2/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Called num 55789123

*Dec 14 23:51:55.882: ISDN Se0/2/0:15 Q931: TX -> SETUP pd = 8 callref = 0x021B

Bearer Capability i = 0x8090A3

Standard = CCITT

Transer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA9839F

Exclusive, Channel 31

Progress Ind i = 0x8183 - Origination address is non-ISDN

Calling Party Number i = 0x0180, '9506'

Plan:ISDN, Type:Unknown

Called Party Number i = 0x81, '55789123'

Plan:ISDN, Type:Unknown

*Dec 14 23:51:55.910: ISDN Se0/2/0:15 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x821B

Cause i = 0x829F - Normal, unspecified

CCME_LM#

paolo bevilacqua · ‎12-15-2006

The switch is actually rejecing the call but no cause is given. Have you tried to place the call with national plan, there is more than one way to do that the easier is at interface level i believe.

wflores · ‎12-15-2006

Hello p.bevilacqua

I have not tried it,

could you tell me how to place the call with national plan??

Thank very much

WF

paolo bevilacqua · ‎12-16-2006

Just configure numbering-type national under the relevant dial-peer.

Let us know how it works.

wflores · ‎12-17-2006

Besides de type national, this is E1 has 6 GDN.

Could you tell me how to configure the CME for an extension to send his DID instead of the GDN.

THANK VERY MUCH

REGARDS

paolo bevilacqua · ‎12-17-2006

First you configure a dialplan and did. The under PRI dialpeer configure a calling-number voice translation rune. Possibly the local number with area code will work.

Are you able to call out now?

Let us know how it works and rate post if appropriate... thanks.

wflores · ‎12-18-2006

I am not able to call out, even I added type national on dial-peer on pri e1 0/2/0.

The E1 ISDN PRI HAS 6 GDN, EACH WITH A 5 TRUNKS:

GDN 2413-3500 TRUNKS 1 AL 5

2413-3535 TRUNKS 6 AL 10

2413-3565 TRUNKS 11 AL 15

2413-3599 TRUNKS 17 AL 21

2413-3550 TRUNKS 22 AL 26

2413-3499 TRUNKS 27 AL 31

HOW TO CONFIGURE THE CME TO ASIGNED EACH GND TO HIS TRUNKS????

The incoming call GDN 24133500 to an extension 4011 works fine, here it is a capture.

CCME_LM#

*Dec 18 21:07:30.167: ISDN Se0/2/0:15 Q931: RX <- SETUP pd = 8 callref = 0x004B

Sending Complete

Bearer Capability i = 0x8090A3

Standard = CCITT

Transer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA98394

Exclusive, Channel 20

Calling Party Number i = 0x0083, '54820634'

Plan:Unknown, Type:Unknown

Called Party Number i = 0x81, '24133599'

Plan:ISDN, Type:Unknown

*Dec 18 21:07:30.179: ISDN Se0/2/0:15 Q931: TX -> CALL_PROC pd = 8 callref = 0x804B

Channel ID i = 0xA98394

Exclusive, Channel 20

CCME_LM#

*Dec 18 21:07:30.183: ISDN Se0/2/0:15 Q931: TX -> ALERTING pd = 8 callref = 0x804B

Progress Ind i = 0x8188 - In-band info or appropriate now available

CCME_LM#

*Dec 18 21:07:36.971: ISDN Se0/2/0:15 Q931: TX -> CONNECT pd = 8 callref = 0x804B

*Dec 18 21:07:37.003: ISDN Se0/2/0:15 Q931: RX <- CONNECT_ACK pd = 8 callref = 0x004B

CCME_LM#

*Dec 18 21:07:37.003: %ISDN-6-CONNECT: Interface Serial0/2/0:19 is now connected to 54820634 N/A

CCME_LM#

*Dec 18 21:07:40.211: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/2/0:19, changed state to up

CCME_LM#

*Dec 18 21:07:48.579: %ISDN-6-DISCONNECT: Interface Serial0/2/0:19 disconnected from 54820634 , call lasted 11 seconds

CCME_LM#

*Dec 18 21:07:48.579: ISDN Se0/2/0:15 Q931: TX -> DISCONNECT pd = 8 callref = 0x804B

Cause i = 0x8090 - Normal call clearing

*Dec 18 21:07:48.631: ISDN Se0/2/0:15 Q931: RX <- RELEASE pd = 8 callref = 0x004B

*Dec 18 21:07:48.631: ISDN Se0/2/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x804B

BUT FOR THE CALL OUT, I SENT A GDN 24133499 DOES NOT GET THROUGH HERE IT IS THE CAPTURE.

CCME_LM#

*Dec 18 22:43:58.223: ISDN Se0/2/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Calling num 24133499

*Dec 18 22:43:58.223: ISDN Se0/2/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Called num 24131600

*Dec 18 22:43:58.223: ISDN Se0/2/0:15 Q931: TX -> SETUP pd = 8 callref = 0x031F

Bearer Capability i = 0x8090A3

Standard = CCITT

Transer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA9839F

Exclusive, Channel 31

Progress Ind i = 0x8183 - Origination address is non-ISDN

CCME_LM#

Calling Party Number i = 0x0180, '24133499'

Plan:ISDN, Type:Unknown

Called Party Number i = 0x81, '24131600'

Plan:ISDN, Type:Unknown

*Dec 18 22:43:58.251: ISDN Se0/2/0:15 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x831F

Cause i = 0x829F - Normal, unspecified

THANK VERY MUCH FOR HELPING

WF

paolo bevilacqua · ‎12-18-2006

If I understand correctly, the GDN would be five pilot numbers assigned to this PRI.

I don't understand the fixed correlation to the circuit number, but I see the switch selecting a channel in range for the GDN.

I do not see how the call is correctly routed to the wanted extension, as it seem that it goes to a data interface from your capture.

Anyway I understand that only these five numbers can be dialed from outside. Then you want make these pilots ring specific extensions, I think again a voice transformation rule should do that.

It does not seem that the 'non-matching' DID script would help you.

I do not know why you cannot dial after trying national and ISDN dial plans. At the minimum the switch should inform about what is going on but doesn't. One hypothesis, could be the channel order selection. Observe the order the switch select the channels for incoming calls. If is descending, change the order used by the router with isdn bchan-number-order ascending.

All failing is time to ask the telco ..

wflores · ‎12-19-2006

THANK VERY FOR YOUR REPLIES.

I talked to the telco staff, they said that I have to give from the CME from any call.

PLAN:ISDN

TYPE:NATIONAL

SEND THE GDN: 24139599.

I have achieved 2 of 3 items the only that I can not make work is TYPE:NATIONAL.

I added the NUMBERING-TYPE NATIONAL on the dial peer.

When I ran the command: "debug isdn q931", I had the following capture:

TYPE NATIONAL ON DIAL-PEER 801

CME_LM#

CCME_LM#

*Dec 18 18:17:41.940: %CALL_CONTROL-6-NUMBERING_TYPE_NO_MATCH: The called number numbering type did not matchThe event for the callid 801 is being discarded.

*Dec 18 18:17:41.944: ISDN Se0/2/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Calling num 4011

*Dec 18 18:17:41.944: ISDN Se0/2/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Called num 54820634

*Dec 18 18:17:41.944: ISDN Se0/2/0:15 Q931: TX -> SETUP pd = 8 callref = 0x02CC

Bearer Capability i = 0x8090A3

Standard = CCITT

Transer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA9839F

Exclusive, Channel 31

Progress Ind i = 0x8183 - Origination address is non-ISDN

CCME_LM#

Calling Party Number i = 0x0180, '4011'

Plan:ISDN, Type:Unknown

Called Party Number i = 0x81, '54820634'

Plan:ISDN, Type:Unknown

*Dec 18 18:17:41.968: ISDN Se0/2/0:15 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x82CC

Cause i = 0x829F - Normal, unspecified

CCME_LM#

------------------------------------------------------------------------------------------

This is the part of the configuration

!

dial-peer voice 801 pots

translation-profile incoming pstn-incoming2

numbering-type national

destination-pattern #9T

translate-outgoing calling 2

incoming called-number 24133599

clid network-number 24133599

direct-inward-dial

port 0/2/0:15

--------------------------------------------

-------------------------------------------

Something that I dont see normal is on capture:

Progress Ind i = 0x8183 - Origination address is non-ISDN

I can not yet call out.

THANKS.

HELP ME PLEASE..........

paolo bevilacqua · ‎12-19-2006

W,

isdn map address will let you change both plan and type.

http://cisco.com/en/US/products/ps6350/products_configuration_guide_chapter09186a0080444966.html

PI 0x8183 is normal, do not worry about it.