05-24-2014 02:28 PM - edited 03-16-2019 10:53 PM
We have CUCM 9.1(1)/Unity Connection 9.1(1) integrated with iLBC codec via SIP trunk from CUCM. Works fine internally.
User's 7965 rings but PSTN hears fast busy upon CFB/CFNA to voicemail. CCM traces show transcoder being invoked (we don't have one setup, I was wanting MGCP gateway to Unity Connection to be iLBC no xcoder by design)
Doesn’t appear that my IOS15-1/2811/MGCP/PVDM2-48 can do iLBC….or do I have something wrong with my mgcp config? Everything else works great but this SIP/iLBC setup.
voice-card 0
dsp service dspfarm
codec complexity flex
!
controller t1 0/0/0
pri-group timeslots 1-4 service mgcp
!
interface Serial0/0/0:23
isdn bind-l3 ccm-manager
!
mgcp codec ilbc
ccm-manager mgcp codec-all
no mgcp
mgcp
debug mgcp packet at gateway I see G711
*May 24 21:50:34.933: MGCP Packet sent to 10.12.5.11:2427--->
200 526 OK
I: 3
v=0
c=IN IP4 10.12.65.254 <<<Gateway IP
m=audio 16948 RTP/AVP 0 100 <<<<shows g711, and no iLBC capability
a=rtpmap:100 X-NSE/8000
a=fmtp:100 192-194
<---
05-25-2014 03:12 AM
Hi Jason,
You might want to try one of the fixed versions of the following bug
https://tools.cisco.com/bugsearch/bug/CSCtw78163/?reffering_site=dumpcr
Symptom:
iLBC codec on MGCP GW not supported with IOS 15.2(1)T
Conditions:
MGCP GW configuration:
===================
ccm-manager mgcp codec-all
mgcp codec ilbc mode 20 packetization-period 60
CUCM configuration:
=================:
region with iLBC settings created
Workaround:
it works with earlier IOS (15.1(3)T2)
HTH
Manish
05-25-2014 05:17 AM
I am running c2800nm-advipservicesk9-mz.151-4.M7.bin
The bug ID indicates it is only for 15.2T. But it would imply that this should work.
However I can change from 15.1.4M7 to 15.1.4M8 or down to a lower version to see if that fixes it.
05-25-2014 05:46 AM
I changed to 15.1.4M8 (March 2014) the most recent IOS.
I took CUC out of the equation and am just trying to get MGCP/Gateway to 7965/SCCP/8.5.4S to be iLBC and that is failing.
clear log
debug mgcp packet <<<< make test call and view log file
2811#show ver | inc System image
System image file is "flash:c2800nm-advipservicesk9-mz.151-4.M8.bin"
2811#show log | inc L:
L: p:20, a:G.729b, s:off, t:b8
L: p:20, a:G.729b, s:off, t:b8
11-21-2016 08:34 PM
Hi Jason,
Did you find a solution? I'm getting same issue. CUCM is only negotiating G.729 or G.711 not iLBC
These two command are already applied on MGCP GW:
ccm-manager mgcp codec-all
mgcp codec ilbc
Running version Version 15.1(4)M10 and CUCM 9.1.2.
Thanks in advance
Regards
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide