Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Inbound Dial-Peer Matching Question

I have created separate dial-peers for inbound and outbound calls on th same voice-port (FXS) and I am not sure why a particular dial-peer is being match on the inbound call. If you look at my configuration below, a call is coming in from port 0/2/0 and it is matching the 301 pots dial-peer instead of 401 pots dial-peer. I thought that if I configured one dial-peer with "incoming called number ." and one with "destination-pattern", the dial-peer with "incoming called-number ." would be matched first. Now if dial-peer 301 is entered into the configuration below dial-peer 401, dial-peer 401 is selected first but I am not sure why.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

dial-peer voice 101 pots

description Incoming Calls Dial Peer

incoming called-number .

direct-inward-dial

port 0/1/0:23

!

dial-peer voice 201 pots

description Outgoing Calls Dial Peer

destination-pattern 9T

port 0/1/0:23

!

dial-peer voice 301 pots

description Outgoing Calls to FXS-01

destination-pattern 7607102824

port 0/2/0

!

dial-peer voice 401 pots

description Incoming Calls from FXS-01

translation-profile incoming INBOUND_FROM_FXS_TO_CUBE

incoming called-number .

port 0/2/0

!

dial-peer voice 402 pots

description Incoming Calls from FXS-02

translation-profile incoming INBOUND_FROM_FXS_TO_CUBE

incoming called-number .

port 0/2/1

!

dial-peer voice 501 voip

description Outgoing Analog Dial-Peer to CUBE01

translation-profile outgoing OUTBOUND_TO_VZBSBC01

preference 1

destination-pattern 0001T

session protocol sipv2

session target ipv4:XXX.XXX.XXX.XXX

voice-class codec 2

dtmf-relay h245-alphanumeric

fax-relay ecm disable

fax-relay sg3-to-g3

fax rate 14400

fax nsf 000000

fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw

ip qos dscp cs5 media

no vad

!

dial-peer voice 502 voip

description Outgoing Analog Dial-Peer to CUBE02

translation-profile outgoing OUTBOUND_TO_VZBSBC01

preference 2

destination-pattern 0001T

session protocol sipv2

session target ipv4:XXX.XXX.XXX.XXX

voice-class codec 2

dtmf-relay h245-alphanumeric

fax-relay ecm disable

fax-relay sg3-to-g3

fax rate 14400

fax nsf 000000

fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw

ip qos dscp cs5 media

no vad

!

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Any advice is greatly appreciated!

Thanks,

Tom

Everyone's tags (2)
1 REPLY
New Member

Inbound Dial-Peer Matching Question

Hi,

Below link with details the rules and priorities for dial-peer (inbound and outbound).

http://www.cisco.com/en/US/docs/ios/12_2/voice/configuration/guide/vvfpeers.html

Regards.

J Rosa.

3311
Views
0
Helpful
1
Replies
CreatePlease login to create content