Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

IOS voice translation-rule/profile issue

Hello everyone... I'm guessing this will be an easy fix, but I don't work with h.323 gateway config often.

I have the carrier delivering DID 5540-5559 (there are a few more ranges like this, but I am concentrating on this one to keep it simple to start off), which I am trying to map to internal extensions 4400-4419. This is the attempt I am making that isn't working:

...

!

voice translation-rule 1

rule 1 /^554/ /440/

rule 2 /^555/ /441/

rule 3 /^556/ /442/

rule 4 /^5573/ /4437/

rule 5 /^5570/ /4430/

rule 6 /^558/ /444/

rule 7 /^5597/ /4457/

rule 8 /^5601/ /4461/

rule 9 /^5612/ /4472/

!

!

voice translation-profile rochester-inbound

translate called 1

!

...

!

voice-port 1/0:0

!

dial-peer voice 4400 voip

destination-pattern 44..

session target ipv4:xxx.xxx.xxx.xxx

dtmf-relay h245-alphanumeric

codec g711ulaw

no vad

!

dial-peer voice 5500 pots

description Inbound calls from PSTN

translation-profile incoming rochester-inbound

destination-pattern 55..

incoming called-number 55..

port 1/0:0

!

...

The result I get from the 'debug voice translation-rule' when I dial 5540 from the PSTN is:

4d06h: //-1/F7578B518377/RXRULE/regxrule_stack_pop_RegXruleNumInfo: stack=0x8349

3D70; count=2

4d06h: //-1/xxxxxxxxxxxx/RXRULE/regxrule_get_profile_from_trunkgroup_internal: V

oice port 0x8370A210 does not belong to any trunk group

4d06h: //-1/FD70F089837A/RXRULE/regxrule_stack_pop_RegXruleNumInfo: stack=0x8409

937C; count=1

4d06h: //-1/FD70F089837A/RXRULE/regxrule_stack_push_RegXruleNumInfo: stack=0x840

9937C; count=0

4d06h: //-1/FD70F089837A/RXRULE/regxrule_stack_push_RegXruleNumInfo: stack=0x840

9937C; count=1

4d06h: //-1/FD70F089837A/RXRULE/regxrule_dp_translate: No profile found in peer

5500 for outgoing direction

4d06h: //-1/FD70F089837A/RXRULE/regxrule_dp_translate: calling_number= calling_o

ctet=0x0

called_number=5540 called_octet=0x81

redirect_number= redirect_type=0 redirect_plan=0 redirect_PI=0 re

direct_SI=0

4d06h: //-1/FD70F089837A/RXRULE/regxrule_vp_translate: No profile found in voice

port or trunk group for outgoing direction

4d06h: //-1/FD70F089837A/RXRULE/regxrule_vp_translate: calling_number= calling_o

ctet=0x0

called_number=5540 called_octet=0x81

redirect_number= redirect_type=0 redirect_plan=0

4d06h: //-1/FD70F089837A/RXRULE/regxrule_stack_pop_RegXruleNumInfo: stack=0x8409

937C; count=2

Using 12.3(4)T1 on this 2621 with only 1 CAS T1 on 1/0:0.

2 REPLIES
Green

Re: IOS voice translation-rule/profile issue

I normally use test voice translation rule to test before.

If it is CAS not sure if rules will apply the same.

Could you please run the following debugs:

debug voice ccapi inou

debug vpm signal

debug voice translation-rule

debug dialpeer

thanks

New Member

Re: IOS voice translation-rule/profile issue

Hi, try applying your inbound translation profile to your voice port.

e.g.

!

voice-port 1/0:0

translation-profile incoming rochester-inbound

!

Your voice translation rules (no.s 1&2 at least) are correct.

If you are still having problems post the same debug back in here and add another one with just the dial-peer debugging on.

Glenn

2272
Views
0
Helpful
2
Replies