Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

%IP-3-DESTHOST : how to fix it?

Hi

I experience a problem about transferring calls from an CUE 7.1 auto attendant console to CCM4.

Calls are comming in a 1st gateway (GW-1),

and it is forwarded to the Autoattendant (aa.aef) that is in the CUE in another CUCME router.(GW2)


The operator is in the CUCM 4.2.

Scenario :

0. caller A make call trhoug an E1 PRI.

1. call arrive int GW-1 (that has PRI)

2. Call is Transfered to CUE (GW-2) auto attendant

3. from CUE calle A push 0 to call the operator

4. Operator is in a CUCM, and  phone ring

5. Operator want to trransfert to a destination B (eg using transfer full consult)

5.1 When transfer : the end destination (B) hears the operator

5.2 after pushing the buttun "transfer", the call seems be transfered.

5.3 Caller A cannot hear caller B. and call is disconnected.

Is there any solution?

CUCME router (GW2) give the error :

=========================

Jul 20 08:39:17.443: %IP-3-DESTHOST: src=10.11.4.2, dst=0.0.0.0, NULL desthost -Process= "VOIP_RTCP", ipl= 0, pid= 308,  -Traceback= 0x418B162C 0x41FD331C 0x41FD4334 0x41FD491C
Jul 20 08:39:21.711: %IP-3-DESTHOST: src=10.11.4.2, dst=0.0.0.0, NULL desthost -Process= "VOIP_RTCP", ipl= 0, pid= 308,  -Traceback= 0x418B162C 0x41FD331C 0x41FD4334 0x41FD491C
Jul 20 08:39:25.763: %IP-3-DESTHOST: src=10.11.4.2, dst=0.0.0.0, NULL desthost -Process= "VOIP_RTCP", ipl= 0, pid= 308,  -Traceback= 0x418B162C 0x41FD331C 0x41FD4334 0x41FD491C
Jul 20 08:39:30.575: %IP-3-DESTHOST: src=10.11.4.2, dst=0.0.0.0, NULL desthost -Process= "VOIP_RTCP", ipl= 0, pid= 308,  -Traceback= 0x418B162C 0x41FD331C 0x41FD4334 0x41FD491C
Jul 20 08:39:33.295: %IP-3-DESTHOST: src=10.11.4.2, dst=0.0.0.0, NULL desthost -Process= "VOIP_RTCP", ipl= 0, pid= 308,  -Traceback= 0x418B162C 0x41FD331C 0x41FD4334 0x41FD491C
Jul 20 08:39:39.855: %IP-3-DESTHOST: src=10.11.4.2, dst=0.0.0.0, NULL desthost -Process= "VOIP_RTCP", ipl= 0, pid= 308,  -Traceback= 0x418B162C 0x41FD331C 0x41FD4334 0x41FD491C
========================

The result of error decoder is in this link :

http://www.cisco.com/cgi-bin/Support/Errordecoder/index.cgi?action=search&locale=en&index=all&query=%25IP-3-DESTHOST&counter=0&paging=5&links=reference&sa=Submit

==============
! GW2 IOS is: Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(22)YB, RELEASE SOFTWARE (fc2)

===============
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
sip
  bind control source-interface GigabitEthernet0/0
  bind media source-interface GigabitEthernet0/0
!

dial-peer voice 2672 voip

description to AAttendant
destination-pattern 2672
session protocol sipv2
session target ipv4:10.11.4.3
dtmf-relay rtp-nte
codec g711ulaw
!

There is a transcoder, MTP, CFB

===================

regards,

Antra

2 REPLIES
New Member

Re: %IP-3-DESTHOST : how to fix it?

This can be IP connectivity issue between your gateway and IP phone B.  As a result RTP stream from phone B to Gateway does not make it.

"5.3 Caller A cannot hear caller B."

1. What is the IP address of  GigabitEthernet0/0

Try to do extended ping from the gateway using GigabitEthernet0/0 address and the IP address of the phone B.  If you do not get reply this is your answer you need to fix IP connectivity.

-- j

New Member

Re: %IP-3-DESTHOST : how to fix it?

Hi,

I call directly the CUCME to phone B.

Everything is ok.

I called directly from a phone A(PRI)  to phone B : ok

But if the call goes from A ->CUA-AA -> Operator -> B :call is cuted when A is transfered to B.

974
Views
0
Helpful
2
Replies