Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

Ip phone 7911G doesn't boot up

Hi guys,

I've recenlty came across a problem, basically i was receiving a message on the display of the phone "ethernet disconnected", i've change cable, i've changed port on the switch with no luck. Searching the web i found a combination to factory reset the phone. After resetting the phone, the phone doesn't display anything. As soon as i  plug the power cord the red and green led blinks and can't see anything on the display.

I think i've erased everything on the phone. I've tried also some suggestions on the internet to reinstall the firmware using tftp also with no luck.

Could you please assist me step by step how to bring this phone back to life

Best Regards

Stelios

Everyone's tags (7)
11 REPLIES
Hall of Fame Super Gold

Re: Ip phone 7911G doesn't boot up

If the phone could not detect ethernet, it is faulty and must be replaced.

Ip phone 7911G doesn't boot up

I've changed cable and port and was still the same..

Hall of Fame Super Gold

Ip phone 7911G doesn't boot up

That is why I'm telling you have a faulty phone.

Ip phone 7911G doesn't boot up

Paolo if it was faulty, and the problem was actually the port on the phone, why it get's power over ethernet as soon as i plug it in on a switch port and the leds on the phone are blinking.

You can see exactly which is my problem in the following link

http://www.youtube.com/watch?v=bCuy22oF_Io

Blue

Ip phone 7911G doesn't boot up

Hi,

Try to power it by local power. I also suspect fault phone and Raising Cisco TAC and Asking for Replacement would resolve the issue.

Regards

Ronak Patel

Rate helpful posts.

Regards Ronak Patel Rate all helpful post by clicking stars below the answer.

Ip phone 7911G doesn't boot up

I tried it also with local power but still the same problem.  Is there any factory reset procedure that i could follow just to be sure that i've done all troubleshooting before Raising Cisco TAC.

Blue

Ip phone 7911G doesn't boot up

HI

Step 1 Unplug the power cable from the phone and then plug it back in.

The phone begins its power-up cycle.

Step 2 While the phone is powering up, and before the Applications Menu button flashes on and off, press and hold #.

Continue to hold # until the message LED on the handset flashes on and off in sequence in red.

Step 3 Release # and press 123456789*0#.

You can press a key twice in a row, but if you press the keys out of sequence, the factory reset will not take place.

After you press these keys, the message LED on the handset flashes  faster in red, and the phone goes through the factory reset process.

Do not power down the phone until it completes the factory reset process, and the main screen appears.

Regards

Ronak Patel

Rate helpful posts.

Regards Ronak Patel Rate all helpful post by clicking stars below the answer.

Ip phone 7911G doesn't boot up

Ronak thanks a lot for your help. After resetting the phone what should i expect? the phone will have an "image" and the files needed to boot up, or i have to upload all necessary files in order to be able to boot normally?

Blue

Ip phone 7911G doesn't boot up

Hi,

Yes, After factory rest, It will delete all the user done configuration and it will come up as factory setting ip phone.

If it does not booth, you have to raise TAC for RMA.

Regards

Ronak patel

Rate helpful posts by clicking stars below the answer.

Regards Ronak Patel Rate all helpful post by clicking stars below the answer.

Ip phone 7911G doesn't boot up

Most probably its faulty since i followed your procedure and stills dead. Thanks both of you guys for assisting me, have a nice day!

Hall of Fame Super Gold

Ip phone 7911G doesn't boot up

There are, and I have seen them, failures types in which the phone powers up, but ethernet doesn't work.

Please avoid laving mid-scale rating for posts that are 100% correct, and made with the will to help.

4812
Views
12
Helpful
11
Replies