Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Is direct in dial via ISP only supported via DID voice interface cards

If you have a DID feature from an ISP, can you only use a DID based voice interface card?

Thanks in advance again :) 

1 ACCEPTED SOLUTION

Accepted Solutions
VIP Purple

Yes, you can do that.You need

Yes, you can do that.

You need to configure did signal on that particular voice port.

Please refer the link for same

 

http://www.cisco.com/c/en/us/support/docs/voice/analog-signaling-e-m-did-fxs-fxo/24760-confg-vic-2did.html

 

regds,

aman

13 REPLIES

thats true.in analog voice

thats true.

in analog voice port, FXS-DID are famous.

http://www.cisco.com/c/en/us/support/docs/routers/2600-series-multiservice-platforms/15268-vic-2did.html

 

~chintan.

VIP Purple

Hi John, You can also refer

Hi John,

 

You can also refer the link

 

http://www.cisco.com/c/dam/en/us/products/collateral/routers/2800-series-integrated-services-routers-isr/product_data_sheet0900aecd8057f2e0.pdf

 

regds,

aman

VIP Purple

Hi John, you can also refer

Hi John,

 

you can also refer the link

 

http://www.cisco.com/c/en/us/products/collateral/routers/2600-series-multiservice-platforms/product_data_sheet09186a00800921e7.html

 

regds,

aman

New Member

Thanks Aman. I had seen that

Thanks Aman. I had seen that link.

Can DID devices also be used for connecting Cisco phones to routers?

VIP Purple

Hi John, DID is a basically a

Hi John,

 

DID is a basically a service which is offered by TELCO and same needs to be supported on Voice cards.

on these cards , you have voice ports and not ethernet ports.

Cisco IP phones need to be  connected to switch.

 

regds,

aman

New Member

That's correct.And then  I

That's correct.

And then  I guess configure vic-2did in router to receive did calls from ISP. Correct?

VIP Purple

Yes, you can do that.You need

Yes, you can do that.

You need to configure did signal on that particular voice port.

Please refer the link for same

 

http://www.cisco.com/c/en/us/support/docs/voice/analog-signaling-e-m-did-fxs-fxo/24760-confg-vic-2did.html

 

regds,

aman

New Member

Thanks Aman. Much appreciated

Thanks Aman. Much appreciated. You have made the complex simple smiley

VIP Purple

Thanks for rating. [+5] to

Thanks for rating.

 

[+5] to Chintan for knowledge sharing.

 

regds,

aman

New Member

Thanks for your reply Chintan

Thanks for your reply Chintan.

And this would apply to a small business using Cisco phones and routers if they wanted to use this method too then?

New Member

And 1 port could be for fax

And 1 port could be for fax and the other for voice or both could be used for voice then

ports can be used as FXS or

ports can be used as FXS or DID,

if you are planning to use them as FXS then you can attach fax or telephone or both.

 

regards

Chintan

New Member

Thanks Chintan, No, I was

Thanks Chintan, 

No, I was considering Cisco phones attached to routers. 

35
Views
5
Helpful
13
Replies