06-13-2010 06:56 AM - edited 03-15-2019 11:13 PM
Hi All,
I am trying to hairpin calls using 1 PRI in cisco gateway,
call flow
1. call comes in to gateway using PRI port 0/1 with the called number 456xxx.
2. I am matching the call using incoming pots dial-peer and then translating the 456xxx number to 654xxx number and then match an outgoing pots dial-peer and send the call out of the same PRI.
Is this call flow possible? gateway is running H323.
Thanks
Solved! Go to Solution.
06-13-2010 05:53 PM
Milan, you are correct. The commands are not necessary for PSTN to PSTN calls.
However, +5 point to Rob for his continued relentless help!
06-14-2010 06:41 PM
Update IOS.
06-13-2010 07:09 AM
Very much possible .
You can use num-exp rather than translation-profile for minimal configuration (if it doesn't affect any other config).
HTH.
06-13-2010 07:21 AM
Hi Arvind,
Just to add a note to the good tips from Mijanur (+5 points "M")
You will need these commands
voice service voip
h323
allow-connections h323 to h323
Cheers!
Rob
Please support CSC Helps Haiti
06-13-2010 07:29 AM
Thanks @Rob.
But I have a confusion, this is not a IP to IP call (like the concept we have for CUBE), here both of the ingress and outgress calls are over PRI i.e. over TDM channel, do we really need this 'allow-connection' command for this case?
Thanks again!
06-13-2010 05:53 PM
Milan, you are correct. The commands are not necessary for PSTN to PSTN calls.
However, +5 point to Rob for his continued relentless help!
06-13-2010 11:43 PM
Hi All,
Thanks for all your reply, I am getting an assertion failure message when i try to hairpin calls.
I can see calls coming in to the gateway by matching incoming dial-peer and then the called number gets translated and matches the outbound dial-peer but the calls are not going out of PRI. I am getting an assertion failure message after matching the outbound pots dial-peer..
Please suggest.
Thanks,
06-14-2010 06:41 PM
Update IOS.
06-14-2010 12:22 AM
It's my honor to having both of you here, +5 for you too sir for both of your continuous contributions.
@aravindhanelango: please post your running-config, 'sh isdn status' and 'debug isdn q931' while failing the call.
06-15-2010 12:11 AM
Hi All,
I was able to simulate the hairpinning with different gateway running same IOS and with same configuration.
It seems i was hitting a bug with that gateway.
Thanks for all your help..
Please find the config which i used...
voice translation-rule 1
rule 1 /4734490/ /94544653/
!
!
voice translation-profile test
translate called 1
controller E1 0/1/0
framing NO-CRC4
pri-group timeslots 1-31
description >>> PRI E10 <<<<
interface Serial0/1/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
no cdp enable
dial-peer voice 100 pots
translation-profile incoming test
incoming called-number 4734490
direct-inward-dial
port 0/1/0:15
!
dial-peer voice 200 pots
destination-pattern 94544653
port 0/1/0:15
forward-digits 7
I have also attached the Q931 debug for a successful call.
06-15-2010 06:48 AM
So you got your answer, it's the IOS.
Try to get next/previous release of your IOS, please read the known issues first before downloading it from CCO.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: