Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
8300
Views
21
Helpful
20
Replies

ISDN E1 - 2801 - 64 DSP - %Insufficient resources to create pri-group

Go to solution
nwkotze
Level 1
Level 1

‎07-13-2009 03:24 AM - edited ‎03-15-2019 06:56 PM

OVR-LAN-V-GW1#sho inv

NAME: "chassis", DESCR: "2801 chassis"

PID: CISCO2801 , VID: VN/A, SN:

NAME: "VIC 0", DESCR: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1"

PID: VWIC2-2MFT-T1/E1 , VID: V01 , SN:

NAME: "PVDM 0", DESCR: "PVDMII DSP SIMM with four DSPs"

PID: PVDM2-64 , VID: V01 , SN:

S2S-OVR-LAN-V-GW1#

card type e1 0 0

network-clock-participate wic 0

network-clock-select 1 E1 0/0/0

isdn switch-type primary-net5

!

controller E1 0/0/0

framing NO-CRC4

S2S-OVR-LAN-V-GW1(config-controller)#pri-group timeslots 1-31

% Not all config may be removed and may reappear after reactivating the logical-interface/sub-interfaces

% Not all config may be removed and may reappear after reactivating the logical-interface/sub-interfaces

% Not all config may be removed and may reappear after reactivating the logical-interface/sub-interfaces

% Not all config may be removed and may reappear after reactivating the logical-interface/sub-interfaces

% Not all config may be removed and may reappear after reactivating the logical-interface/sub-interfaces

% Not all config may be removed and may reappear after reactivating the logical-interface/sub-interfaces

% Not all config may be removed and may reappear after reactivating the logical-interface/sub-interfaces

% Not all config may be removed and may reappear after reactivating the logical-interface/sub-interfaces

% Not all config may be removed and may reappear after reactivating the logical-interface/sub-interfaces

% Not all config may be removed and may reappear after reactivating the logical-interface/sub-interfaces

% Not all config may be removed and may reappear after reactivating the logical-interface/sub-interfaces

% Not all config may be removed and may reappear after reactivating the logical-interface/sub-interfaces

% Not all config may be removed and may reappear after reactivating the logical-interface/sub-interfaces

% Not all config may be removed and may reappear after reactivating the logical-interface/sub-interfaces

% Not all config may be removed and may reappear after reactivating the logical-interface/sub-interfaces

%Insufficient resources to create pri-group - it has been removed

S2S-OVR-LAN-V-GW1(config-controller)#

S2S-OVR-LAN-V-GW1#sho flash

-#- --length-- -----date/time------ path

1 27352008 Jul 10 2009 17:39:42 +01:00 c2801-spservicesk9-mz.124-25a.bin

36532224 bytes available (27353088 bytes used)

sho ver:

System image file is "flash:c2801-spservicesk9-mz.124-25a.bin"

Cisco 2801 (revision 5.0) with 352256K/40960K bytes of memory.

Processor board ID FHK084711TB

2 FastEthernet interfaces

2 Channelized E1/PRI ports

4 DSPs, 64 Voice resources

DRAM configuration is 64 bits wide with parity disabled.

191K bytes of NVRAM.

62592K bytes of ATA CompactFlash

Labels:
0 Helpful
20 Replies 20

Go to solution
nwkotze
Level 1
Level 1

‎07-16-2009 12:46 AM

Errors

1. Two or more items are incompatible. Selected or default-included item: [S280IPB-12415T] is incompatible with: [ PVDM2-64 ]. Please change one or more items.

To correct this error REPLACE the S280IPB-12415T from the following options

(2801 SOFTWARE:S280IPB:S280IPB-12415T)

S280AESK9-Advanced Enterprise Services

S280AISK9-Advanced IP Services

S280ES-Enterprise Services

S280ESK9-Enterprise Services w/Security

S280IPV-IP Voice

S280IPVK9-IP Voice w/Security

S280SPSK9-SP Services

OR

To correct this error REMOVE from the following options

PVDM2-64

64-Channel Packet Voice/Fax DSP Module

(2801 PVDM 0:PVDM2-64)

0 Helpful

Go to solution
pcameron
Cisco Employee
Cisco Employee
In response to nwkotze

‎07-16-2009 01:12 AM

12.4.15T IP Base software is not "incompatible" with the PVDM2-64 DSP module. This code does not have any voice features, so the DSP and the voice cards won't be recognised and you will not be able to configure anything voice related.

Assuming you do have the correct version of code, does this have any relevance to moving the E1 card out of slot 0 into the recommended slot so PRI can be configured?

0 Helpful

Go to solution
nwkotze
Level 1
Level 1
In response to nwkotze

‎07-16-2009 01:48 AM

controller E1 0/3/0

!

controller E1 0/3/1

!

ip tcp synwait-time 10

S2S-OVR-LAN-V-GW1#config t

Enter configuration commands, one per line. End with CNTL/Z.

S2S-OVR-LAN-V-GW1(config)#controller E1 0/3/0

S2S-OVR-LAN-V-GW1(config)#network-clock-participate wic 3

S2S-OVR-LAN-V-GW1(config)#controller E1 0/3/0

S2S-OVR-LAN-V-GW1(config-controller)#pri-group timeslots 1-31

S2S-OVR-LAN-V-GW1(config-controller)#

*Jul 16 10:04:26.515: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(1), changed state to up

*Jul 16 10:04:26.519: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(2), changed state to up

*Jul 16 10:04:26.519: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(3), changed state to up

*Jul 16 10:04:26.519: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(4), changed state to up

*Jul 16 10:04:26.519: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(5), changed state to up

*Jul 16 10:04:26.519: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(6), changed state to up

*Jul 16 10:04:26.519: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(7), changed state to up

*Jul 16 10:04:26.519: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(8), changed state to up

*Jul 16 10:04:26.519: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(9), changed state to up

*Jul 16 10:04:26.519: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(10), changed state to up

*Jul 16 10:04:26.519: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(11), changed state to up

*Jul 16 10:04:26.519: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(12), changed state to up

*Jul 16 10:04:26.519: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(13), changed state to up

*Jul 16 10:04:26.519: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(14), changed state to up

*Jul 16 10:04:26.519: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(15), changed state to up

*Jul 16 10:04:26.519: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(17), changed state to up

*Jul 16 10:04:26.519: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(18), changed state to up

*Jul 16 10:04:26.519: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(19), changed state to up

*Jul 16 10:04:26.523: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(20), changed state to up

*Jul 16 10:04:26.523: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(21), changed state to up

*Jul 16 10:04:26.523: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(22), changed state to up

*Jul 16 10:04:26.523: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(23), changed state to up

*Jul 16 10:04:26.523: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(24), changed state to up

*Jul 16 10:04:26.523: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(25), changed state to up

*Jul 16 10:04:26.523: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(26), changed state to up

*Jul 16 10:04:26.523: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(27), changed state to up

*Jul 16 10:04:26.523: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(28), changed state to up

*Jul 16 10:04:26.523: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(29), changed state to up

*Jul 16 10:04:26.523: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(30), changed state to up

*Jul 16 10:04:26.523: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(31), changed state to up

S2S-OVR-LAN-V-GW1(config-controller)#end

S2S-OVR-LAN-V-GW1#wr

Building configuration...

Compressed configuration from 4929 bytes to 2935 bytes

*Jul 16 10:04:46.975: %SYS-5-CONFIG_I: Configured from console by console[OK]

S2S-OVR-LAN-V-GW1#dir

Directory of flash:/

1 -rw- 33034640 Jul 16 2009 11:47:00 +01:00 c2801-ipvoice-mz.124-15.T9.bin

63877120 bytes total (30838784 bytes free)

S2S-OVR-LAN-V-GW1#

0 Helpful

Go to solution
pcameron
Cisco Employee
Cisco Employee
In response to nwkotze

‎07-16-2009 04:50 AM

So ... it's all OK now ?

0 Helpful

Go to solution
nwkotze
Level 1
Level 1
In response to pcameron

‎07-16-2009 04:57 AM

Yes, I got it working!!

0 Helpful

Go to solution
angel.gino
Level 1
Level 1

‎05-03-2011 06:37 AM

I had the same problem. It moved vwic to slot 0 and it worked.

Thanks for the solution.

0 Helpful
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Customers Also Viewed These Support Documents