Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Attention: The Community will be in read-only mode on 12/14/2017 from 12:00 am pacific to 11:30 am.

During this time you will only be able to see content. Other interactions such as posting, replying to questions, or marking content as helpful will be disabled for few hours.

We apologize for the inconvenience while we perform important updates to the Community.

New Member

isdn incorrect calling number display?

Hi Everybody,

I tried to make a call from CUCM's IP Phone to my mobile phone through the VG's T1

I have started the "debug isdn q931", and see

Calling Party Number is 3555 7000,

Called Party Number is 6699 4488 (my mobile)

Howevery, my mobile shows the Caller Display is "3555 7100" , I suppose it should be "35557000" ....

What else could make this happen? is it because the Telecom has wrongly converted my Calling Number? or there is any conflict in CUCM?

Here is the result of debug q931

===============================================================================

ISDN Se0/0/1:23 Q931: Tx -> SETUP pd = 8 callref = 0x000B

    Bearer Capability i = 0x8090A2

        Standard = CCITT

        Transfer Capability = Speech

        Transfer Mode = Circuit

        Transfer Rate = 64 kbit/s

    Cannel ID i = 0xA98397

        Exclusive, Channel 23

    Calling Party Number i = 0x0081, '35557000'

        Plan:Unknown, Type:Unknown

    Called Party Number i = 0x80, '66994488'

        Plan:Unknown, Type:Unknown

ISDN Se0/0/1:23 Q931: Rx <- SETUP_ACK pd = 8 callref = 0x800B

    Channel ID i = 0xA98397

        Exclusive, Channel 23

ISDN Se0/0/1:23 Q931: Rx <- CALL_PROC pd = 8 callref = 0x800B

    Progress Ind i = 0x8288 - In-band info or appropriate now available

ISDN Se0/0/1:23 Q931: Rx <- ALERTING pd = 8 callref = 0x800B

    Progress Ind i = 0x8281 - Call not end-to-end ISDN, may have in-band info

    Progress Ind i = 0x8288 - In-band info or appropriate now available

ISDN Se0/0/1:23 Q931: Rx <- CONNECT pd = 8 callref = 0x800B

    Progress Ind i = 0x8281 - Call not end-to-end ISDN, may have in-band info

ISDN Se0/0/1:23 Q931: Tx -> CONNECT_ACK pd = 8 callref = 0x000B

===============================================================================

Thanks in advance
Sam

Everyone's tags (3)
1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

isdn incorrect calling number display?

This is the info you're sending:

    Calling Party  Number i = 0x0081, '35557000'

        Plan:Unknown, Type:Unknown

If you see something else on the called phone it's because someone in the middle is overwriting that info.

Get in touch with Telco for this matter, if those are DIDs, do you own 7000??? Telcos do this if you do not own the DID and use the main DID number of what you do own.

HTH

java

if this helps, please rate

www.cisco.com/go/pdihelpdesk

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
3 REPLIES
Cisco Employee

isdn incorrect calling number display?

This is the info you're sending:

    Calling Party  Number i = 0x0081, '35557000'

        Plan:Unknown, Type:Unknown

If you see something else on the called phone it's because someone in the middle is overwriting that info.

Get in touch with Telco for this matter, if those are DIDs, do you own 7000??? Telcos do this if you do not own the DID and use the main DID number of what you do own.

HTH

java

if this helps, please rate

www.cisco.com/go/pdihelpdesk

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
New Member

isdn incorrect calling number display?

Thanks for the reply, I think  I have to contact with Telco on tomorrow...

Let see what's happening

Green

isdn incorrect calling number display?

Sam,

Is 3555 7100 your ISDN service billing number ?

Here in the UK we have to pay the TELCO to allow

the DDInumber to go out instead of the billing number.

Regards,
Alex.
Please rate useful posts.

Regards, Alex. Please rate useful posts.
528
Views
5
Helpful
3
Replies
CreatePlease to create content