Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

ISDN PRI configuration on 2800 Problem

We've been using MGCP w/D channel backhaul in the past with no problems. I'm now trying to configure a Cisco 2851 with a PRI using H.323. I can't figure out why my POTS dial peer is showing "down" on "OUT STAT".

AD PRE PASS OUT

TAG TYPE MIN OPER PREFIX DEST-PATTERN FER THRU SESS-TARGET STAT PORT

1 voip up up ....... 1 syst ipv4:10.10.10.10

2 voip up up ....... 2 syst ipv4:10.10.10.11

10 pots up up .T 0 down 1/0:23

PRI Channel Statistics:

ISDN Se1/0:23, Channel [1-24]

Configured Isdn Interface (dsl) 0

Channel State (0=Idle 1=Proposed 2=Busy 3=Reserved 4=Restart 5=Maint_Pend)

Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4

State : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3

Service State (0=Inservice 1=Maint 2=Outofservice 8=MaintPend 9=OOSPend)

Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4

State : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2

controller T1 1/0

framing esf

linecode b8zs

pri-group timeslots 1-24

interface Serial1/0:23

description PRI

no ip address

no logging event link-status

isdn switch-type primary-ni

isdn incoming-voice voice

no cdp enable

dial-peer voice 1 voip

preference 1

destination-pattern .......

voice-class codec 1

voice-class h323 1

session target ipv4:10.10.10.10

incoming called-number .

dtmf-relay h245-signal h245-alphanumeric

no vad

!

dial-peer voice 2 voip

preference 2

destination-pattern .......

voice-class codec 1

voice-class h323 1

session target ipv4:10.10.10.11

incoming called-number .

dtmf-relay h245-signal h245-alphanumeric

no vad

!

dial-peer voice 10 pots

destination-pattern .T

incoming called-number .

direct-inward-dial

port 1/0:23

forward-digits all

Any help would be greatly appreciated.

3 REPLIES
VIP Super Bronze

Re: ISDN PRI configuration on 2800 Problem

Hi,

Can you post the output of your sh isdn status and sh ip interface brief

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
New Member

Re: ISDN PRI configuration on 2800 Problem

XXX-2851#show isdn status serial 1/0:23

Global ISDN Switchtype = primary-4ess

ISDN Serial1/0:23 interface

dsl 0, interface ISDN Switchtype = primary-ni

Layer 1 Status:

ACTIVE

Layer 2 Status:

TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED

Layer 3 Status:

0 Active Layer 3 Call(s)

Active dsl 0 CCBs = 0

The Free Channel Mask: 0x807FFFFF

Number of L2 Discards = 0, L2 Session ID = 1

Total Allocated ISDN CCBs = 0

BOA-2851#show ip interface brief

Interface IP-Address OK? Method Status Protocol

GigabitEthernet0/0 172.26.3.1 YES NVRAM up up

GigabitEthernet0/1 172.26.4.1 YES NVRAM up up

Serial0/1/0 unassigned YES NVRAM up up

Serial0/2/0 unassigned YES NVRAM down down

Serial0/3/0 unassigned YES NVRAM up up

Serial1/0:0 unassigned YES unset down down

Serial1/0:1 unassigned YES unset down down

Serial1/0:2 unassigned YES unset down down

Serial1/0:3 unassigned YES unset down down

Serial1/0:4 unassigned YES unset down down

Serial1/0:5 unassigned YES unset down down

Serial1/0:6 unassigned YES unset down down

Serial1/0:7 unassigned YES unset down down

Serial1/0:8 unassigned YES unset down down

Serial1/0:9 unassigned YES unset down down

Serial1/0:10 unassigned YES unset down down

Serial1/0:11 unassigned YES unset down down

Serial1/0:12 unassigned YES unset down down

Serial1/0:13 unassigned YES unset down down

Serial1/0:14 unassigned YES unset down down

Serial1/0:15 unassigned YES unset down down

Serial1/0:16 unassigned YES unset down down

Serial1/0:17 unassigned YES unset down down

Serial1/0:18 unassigned YES unset down down

Serial1/0:19 unassigned YES unset down down

Serial1/0:20 unassigned YES unset down down

Serial1/0:21 unassigned YES unset down down

Serial1/0:22 unassigned YES unset down down

Serial1/0:23 unassigned YES manual up up

Re: ISDN PRI configuration on 2800 Problem

Hello,

Layer 2 needs to say MULTIPLE_FRAME_ESTABLISHED. Do term mon and debug isdn q921 and see what the output is and post it.

Hope that helped, if so please rate.

396
Views
0
Helpful
3
Replies
CreatePlease to create content