cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
970
Views
5
Helpful
13
Replies

ISDN PRI incoming calls problem

aamirdhedhi
Level 1
Level 1

Guys,

I am having a bit of a trouble here, i am able to make out going calls for all the extensions, but on an inbound call from out side on any of the PRI numbers, i get a dial tone after dialing, after which if i dial the extension number, the extension rings other wise not can any one please help me out to resolve this issue i am also attaching the config file.

13 Replies 13

paolo bevilacqua
Hall of Fame
Hall of Fame

Your DP 1 is not matching the called number:

dial-peer voice 1 pots

incoming called-number 1..

Change to what you see in "debug isdn q931" and the call will accepted.

I don't know if you have DID and if so what "dialplan-pattern" is needed under telephony-service. That is also needed to ring the extensions directly from outside.

thanks for ur reply i had tried using 1.. in dial peer but it did not work

i also configured dialplan patter

the DID range is from 8020100 to 8020299

So configure incoming called-number 8020...

You can remove the port from the incoming DP, it is not used.

and "dialplan-pattern 1 8020... extension-length 3"

As an appreciation to those providing answers, please rate useful posts using the scrollbox below!

i tried the paramaters mentioned still the same.

Then just use .. for incoming called-number in the DP that has direct-inward-dial. Or take debugs isdn q931 with term mon and place the correct number.

ok i ll try this tomorrow and reply abt the result

anderson-david
Level 3
Level 3

Hi,

put the cmd "direct-inward-dial" under your POTS dial peers this should stop the secondary dial tone, also how many digits is your service provider presenting BT present 6 by default so unless you have asked for only 3 to be presented you will need a translation pattern to change the incoming 6 digits to 3.

I hope this helps

Dear Anderson

the number provided by the telco is 8020222 the range i have been given is 8020100 to 299.i hav configrued the extensions starting from 100 to 135 i have arleady put direct-inward-dial. can u tell me how to do the translation.

Cheers

aamir

The command under telephony-service is:

dialplan-pattern 1 8020... extension-len 3

This assumes telco is sending 7 digits for called number thing that you can verify with "term mon" and "debug isdn q931".

Dear the following is the result of debug isdn q931

Sending Complete

Bearer Capability i = 0x9090A3

Standard = CCITT

Transfer Capability = 3.1kHz Audio

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA98388

Exclusive, Channel 8

Progress Ind i = 0x8483 - Origination address is non-ISDN

Calling Party Number i = 0x2183, '048850447'

Plan:ISDN, Type:National

Called Party Number i = 0x81, '0122'

Plan:ISDN, Type:Unknown

Sep 8 07:20:15.386: ISDN Se0/0/1:15 Q931: TX -> CALL_PROC pd = 8 callref = 0x9

D52

Channel ID i = 0xA98388

Exclusive, Channel 8

Sep 8 07:20:15.386: ISDN Se0/0/1:15 Q931: TX -> CONNECT pd = 8 callref = 0x9D5

2

Sep 8 07:20:15.846: ISDN Se0/0/1:15 Q931: RX <- CONNECT_ACK pd = 8 callref = 0

x1D52

Sep 8 07:20:15.846: ISDN Se0/0/1:15 **ERROR**: call_progress: DEV_CONNECTED VOI

CE ERROR: Bearer capability not available(0x3A): b channel 7 call id 0xF8

can u please go throug and help me

Telco is passing four digits. Use

"incoming called-number 0..." and

"dialplan-pattern 1 0... extension-length 3".

thanks my issue is resloved and i have rated ur post

Thanks for the nice rating and good luck!

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: