Guys,
I am having this issue and i just need to verify, or justify to the telco that my configs are correct and the issue is maybe a loop on their switching
i've tried changing isdn switch-type and related configs to primary-net5 as this is E1, but no changes.
the debugs just show bad frames, i have been following this post as well. Any assistance i can get i will appreciate thanks
https://supportforums.cisco.com/thread/2038702
Config
--------------------------------------
network-clock-participate wic 0
network-clock-select 1 E1 0/0/0
!
controller E1 0/0/0
framing NO-CRC4
pri-group timeslots 1-31
!
interface Serial0/0/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-qsig
isdn incoming-voice voice
isdn sending-complete
no cdp enable
!
-----------------------------------------
Router#sh controllers e1
E1 0/0/0 is up.
Applique type is Channelized E1 - balanced
Description: DIGICEL
No alarms detected.
alarm-trigger is not set
Version info Firmware: 20100222, FPGA: 13, spm_count = 0
Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.
Data in current interval (883 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Total Data (last 60 15 minute intervals):
26 Line Code Violations, 1 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 22 Line Err Secs, 0 Degraded Mins,
22 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Router#sh isdn stat
Global ISDN Switchtype = primary-qsig
ISDN Serial0/0/0:15 interface
dsl 0, interface ISDN Switchtype = primary-qsig
**** Slave side configuration ****
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
TEI = 255, Ces = 255, SAPI = 0, State = TEI_ASSIGNED
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 0 CCBs = 0
The Free Channel Mask: 0xFFFF7FFF
Number of L2 Discards = 0, L2 Session ID = 239
Total Allocated ISDN CCBs = 0
debug isdn q921 is ON.
*Dec 24 15:36:13.260: ISDN Se0/0/0:15 Q921: L2_EstablishDataLink: sending SABME
*Dec 24 15:36:13.260: ISDN Se0/0/0:15 Q921: User TX -> SABMEp sapi=0 tei=127
*Dec 24 15:36:13.260: ISDN Se0/0/0:15 Q921: User RX <- BAD FRAME(0x00FF7F)
*Dec 24 15:36:14.260: ISDN Se0/0/0:15 Q921: User TX -> SABMEp sapi=0 tei=127
Router#
*Dec 24 15:36:14.260: ISDN Se0/0/0:15 Q921: User RX <- BAD FRAME(0x00FF7F)
*Dec 24 15:36:15.260: ISDN Se0/0/0:15 Q921: User TX -> SABMEp sapi=0 tei=127
Router#
*Dec 24 15:36:15.260: ISDN Se0/0/0:15 Q921: User RX <- BAD FRAME(0x00FF7F)
*Dec 24 15:36:16.260: ISDN Se0/0/0:15 Q921: User TX -> SABMEp sapi=0 tei=127
Router#
*Dec 24 15:36:16.260: ISDN Se0/0/0:15 Q921: User RX <- BAD FRAME(0x00FF7F)
---------------------------------------------
debug isdn q931 is ON.
Router##BAD FRAME()
Router#BAD FRAME()
Router#BAD FRAME()
Router#BAD FRAME()
*Dec 24 15:37:29.259: ISDN Se0/0/0:15 Q931: Ux_DLRelInd: DL_REL_IND received from L2
