Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

Issue FXO

hi,

i have call manager 6.1 with a H323 gateway.

in the gateway i have 3 cards:

- one PRI : the calls work hine ( in and out)

- one card 4-Fxo: with 4 analog line : calls work fine (in and out)

- one card 4-fxo: with 4 gateway GSM: calls from site to outside work fine. but the call from outside dosn't work, the phone rings and when i tray to respond the call hang up :

this the config for the 4 voice port:

voice-port 0/3/0

input gain -3

output attenuation 4

echo-cancel coverage 24

no comfort-noise

cptone FR

timeouts interdigit 6

timeouts call-disconnect 5

timing hookflash-out 500

connection plar opx 100

impedance complex2

caller-id enable

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Gold

Re: Issue FXO

Can you try "no battery reversal" ?

If still problem, get "debug vpm signal" with "term mon" for a failed call.

16 REPLIES
New Member

Re: Issue FXO

If the call rings properly, but answering causes a disconnect, this usually indicates a codec problem. Can you please post your dial-peers?

New Member

Re: Issue FXO

thanks for replay

yes the ring is good, but tha call disconnect when i tray to answeer

the problem is with port 0/3/X

this my all dial peer:

dial-peer voice 100 voip

destination-pattern ...

session target ipv4:172.16.0.254

dtmf-relay h245-alphanumeric

codec g711ulaw

!

dial-peer voice 10 pots

destination-pattern 82..........

direct-inward-dial

port 0/0/1

!

dial-peer voice 11 pots

destination-pattern 83..........

incoming called-number 0522335486

direct-inward-dial

port 0/0/2

!

dial-peer voice 12 pots

destination-pattern 84..........

incoming called-number 0522972486

direct-inward-dial

port 0/0/3

!

dial-peer voice 9 pots

destination-pattern 81..........

direct-inward-dial

port 0/0/0

!

dial-peer voice 1 pots

destination-pattern 9..........

direct-inward-dial

port 0/2/0:15

forward-digits 10

!

dial-peer voice 125 pots

destination-pattern 7.............

direct-inward-dial

port 0/2/0:15

forward-digits 13

!

dial-peer voice 126 pots

destination-pattern 800...

direct-inward-dial

port 0/2/0:15

forward-digits 3

!

dial-peer voice 127 pots

destination-pattern 80..

direct-inward-dial

port 0/2/0:15

forward-digits 2

!

dial-peer voice 20 pots

destination-pattern 86..........

port 0/3/0

!

dial-peer voice 21 pots

destination-pattern 87..........

port 0/3/1

!

dial-peer voice 22 pots

destination-pattern 88..........

port 0/3/2

!

dial-peer voice 23 pots

destination-pattern 89..........

port 0/3/3

!

!

Hall of Fame Super Gold

Re: Issue FXO

Try:

voice-port x/y

no supervisory disconnect signal

note, if you use trunk-groups, you can reduce the many DPs to a single one.

New Member

Re: Issue FXO

yes, i have the same config for both card 4-FXO

the first 4 port is connected to 4 analog lines (to telecom company) and all call are fine from inside to outside and from outside from inside.

but the seconde card 4-FXO are connected to 4 gateway GSM (to mobile phone company), i can make the call from inside to other number in the world, but i can't receive the call( just ring and han up when i tray to respond.

New Member

Re: Issue FXO

Have you tried plugging the GSM Gateway lines into the other ports to isolate that it's not the FXO ports?

Hall of Fame Super Gold

Re: Issue FXO

I've corrected my reply above, try and let us know.

New Member

Re: Issue FXO

hi,

this command is to solve another problem, but i have testd this command without result.

yes i have tested the port 0/3/X , they work fine with analog line.

And if the port isn't good i can't make calls from inside to outsider vis this ports.

thanks for advice

New Member

Re: Issue FXO

Are the ports from your GSM Gateway Ground Start?

New Member

Re: Issue FXO

the company phone says that,

how i can use loop Start

Hall of Fame Super Gold

Re: Issue FXO

Loop start is default.

Ground start is not used outside north america.

Hall of Fame Super Gold

Re: Issue FXO

Can you try "no battery reversal" ?

If still problem, get "debug vpm signal" with "term mon" for a failed call.

New Member

Re: Issue FXO

i have read the document: Document ID: 8120

i used all command in this document, but issue doesn't mutch with this trooblshoot document.

thanks for your best effort

Hall of Fame Super Gold

Re: Issue FXO

Nobody said that you have a disconnect supervision problem.

Please collect the debug indicated above.

New Member

Re: Issue FXO

hi,

i attached the debug file

thanks for help

New Member

Re: Issue FXO

That looks like battery reversal is occurring and the Cisco gateway is disconnecting the call. Is this with "no battery-reversal" applied to the voice port?

New Member

Re: Issue FXO

yes this the problem, thanks for all

now all calls are ok

294
Views
0
Helpful
16
Replies
CreatePlease to create content