10-10-2013 04:06 AM - edited 03-16-2019 07:49 PM
Hi All, I am currently facing issue with PRI i can do only 1 outgoing call at time , Service provider tested call on PRI tester its work fine.
10-10-2013 04:13 AM
What is your setup like? can you give us a brief description of your call flow and include all the elements in it.
Also send us the ff:
1. sh run
2. debug voip ccapi in out
3.debug isdn q931
Please rate all useful posts
"opportunity is a haughty goddess who waste no time with those who are unprepared"
10-10-2013 10:08 AM
below is the debug isdn q931
Only 1 outgoing call is working & if i try other then call reaches to receiver number but then no voice hear at both end
Oct 10 10:56:35.234 UTC: ISDN Se0/1/0:15 Q931: TX -> SETUP pd = 8 callref = 0x247B Bearer Capability i = 0x8090A3 Standard = CCITT Transfer Capability = Speech Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA9839E Exclusive, Channel 30 Calling Party Number i = 0x0081, '6615314' Plan:Unknown, Type:Unknown Called Party Number i = 0x80, '04844041491' Plan:Unknown, Type:Unknown Oct 10 10:56:35.298 UTC: ISDN Se0/1/0:15 Q931: RX <- CALL_PROC pd = 8 callref = 0xA47B Channel ID i = 0xA9839E Exclusive, Channel 30 Oct 10 10:56:35.618 UTC: ISDN Se0/1/0:15 Q931: RX <- ALERTING pd = 8 callref = 0xA47B Progress Ind i = 0x8282 - Destination address is non-ISDN Oct 10 10:56:35.938 UTC: hwic_t1e1_wic_bp_connect: setup failed Oct 10 16:26:35.938 IST: %FLEXDSPRM-3-TDM_CONNECT: failed to connect voice-port (0/1/0) to dsp_channel(0/0/1) Oct 10 10:56:35.938 UTC: hwic_t1e1_wic_bp_disconnect: disconnect failed
10-10-2013 11:58 AM
Hello Vijay,
That seems to be the problem:
%FLEXDSPRM-3-TDM_CONNECT: failed to connect voice-port (0/1/0) to dsp_channel(0/0/1)
Could you provide the output of 'show voice dsp' command? Also 'sh inv' and 'sh run' would be useful.
Kind regards,
Andrew C.
10-10-2013 08:05 PM
10-11-2013 06:00 AM
Hi Vijay,
In addition to troubleshooting by Mr. Andrew[+5],can u share show voice dsp group all and show inventory/show diag as well?
regds,
aman
10-18-2013 01:23 AM
Hi issue get resolved after the reload. but its a workaround......
10-18-2013 01:26 AM
You'd better open the case with TAC then, it seems to be the hardware/software problem, not the configuration related thing.
Kind regards,
Andrew C.
10-18-2013 02:15 AM
Hi Vijay,
You can run the command show voice dsp group all and check the State of DSP.[UP/FAIL] when u face the same issue again.
regds,
aman
10-18-2013 09:09 PM
There are a couple of defects with this same behavior. What is the current ios?
-show version
-show voice dsp group all
--
Jorge Armijo
Please remember to rate helpful responses and identify helpful or correct answers.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: