Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

ITS with remote office

Hi,

I have HQ and BR1, i need BR1 people to call the HQ but hit the AA not the extension directly.

I am using the AA ITS not the B-acd. i can see that i can enable it on the voice-port but in my case i have voip not pots

please advice

Good day

7 REPLIES
Hall of Fame Super Gold

Re: ITS with remote office

What is AA ITS ? What prevent you from using B-ACD ?

This said, generally speaking, when a service works for pots, should work for voip too.

New Member

Re: ITS with remote office

Hi,

application

service autoatt flash:its-CISCO.2.0.1.0.tcl

dial-peer voice 10 pots

service autoatt

destination-pattern 9T

port 0/0/0

the customer need from the AA to press the extension or 0 for operator

so what you are saying is that if i do the following it should work

dial-peer voice 11 voip

service autoatt

incoming called number .

I will give it a try

Good day

Hall of Fame Super Gold

Re: ITS with remote office

I think that is just an older version of B-ACD/AA under another name.

You need codec g711u under DP to be able to listen to prompts.

New Member

Re: ITS with remote office

here is the result after the setup

Config

application

service autoatt flash:its-CISCO.2.0.1.0.tcl

paramspace english language en

paramspace english index 1

param operator 1001

paramspace english location flash:

paramspace english prefix en

param en 0

dial-peer voice 1005 voip

service autoatt

incoming called-number 1005

dtmf-relay h245-alphanumeric

codec g711ulaw

!

calling 1005 from another router will result as follow:

debugs:

*Apr 13 07:32:18.633: //64//TCL :/tcl_PutsObjCmd: proc act_Setup

*Apr 13 07:32:18.633:

*Apr 13 07:32:18.633: //64//TCL :/tcl_PutsObjCmd:

proc init_perCallvars

*Apr 13 07:32:18.633:

*Apr 13 07:32:18.633: //64//TCL :/tcl_PutsObjCmd:

ANI 3002

*Apr 13 07:32:18.633:

*Apr 13 07:32:18.633: //64//TCL :/tcl_PutsObjCmd:

DNIS 1005

*Apr 13 07:32:18.633:

*Apr 13 07:32:18.641: //64//TCL :/tcl_PutsObjCmd: IP IVR Disconnect Status = RESULT=di_001

*Apr 13 07:32:18.641:

*Apr 13 07:32:18.641: //64//TCL :/tcl_PutsObjCmd:

Call failed. Play prompt and collect digit

*Apr 13 07:32:18.641:

*Apr 13 07:32:18.641: //64//TCL :/tcl_PutsObjCmd:

proc act_Select

*Apr 13 07:32:18.641:

*Apr 13 07:32:18.641: //64//TCL :/tcl_PutsObjCmd:

proc act_DestBusy

New Member

Re: ITS with remote office

i think it is not supported on VOIP, it plays the disconnect prompt directly, i will try b-acd instead

more debugs:

debug voip application media

CME(config-dial-peer)#

*Apr 13 07:52:06.099: //-1//DPM :DP9:/pc_mc_addToDynamicS: (1) _disconnect.au

*Apr 13 07:52:06.099: //-1//DPM :DP9:/pc_mc_addToDynamicS: Doing : _disconnect.au

*Apr 13 07:52:06.099: //-1//DPM :/mcTokenizerGetNext: savedcharptr=_ endptrptr=_disconnect.au

*Apr 13 07:52:06.099: //-1//DPM :DP9:/pc_mc_addToDynamicS: Token : _disconnect.au status 1

*Apr 13 07:52:06.099: //-1//DPM :DP9:/dp_mcDQfromFileDynamic: pLanguage=en FileName=_disconnect.au

*Apr 13 07:52:06.099: //-1//DPM :DP9:/dp_mcDQfromURL: file=flash:en_disconnect.au

*Apr 13 07:52:06.099: //-1//MCM :/mc_createFromFileUrl: Getting a media content: name=en_disconnect.au

url=flash:en_disconnect.au

load fast, fetchtimeout=-1

*Apr 13 07:52:06.099: //-1//DPM :/mcTokenizerGetNext: savedcharptr= endptrptr=

*Apr 13 07:52:06.099: //31//MSW :/msw_create: cbf=0x41CEDA7C

*Apr 13 07:52:06.099: //-1//MSM :MS15:/ms_create: Iniz ply_timer

*Apr 13 07:52:06.099: //31//MSW :/msw_synth_open: mediaStream 0x45E2CEC8 created

*Apr 13 07:52:06.099: //31//MSW :/msw_synth_open: rtspStream 0x4778D8D0 created,

status=RTSP_STATUS_SUCCESS, session_id=0xF (15)

*Apr 13 07:52:06.099: //31//MSW :/msw_synth_open: AIS : Creating TTS AIS Backend record

*Apr 13 07:52:06.099: //-1//MSM :MS16:/ms_create: Iniz ply_timer

*Apr 13 07:52:06.099: //31//MSW :/msw_recrd_open:

*Apr 13 07:52:06.099: :msw_recrd_open mediaStream 0x46B23BC0 created

*Apr 13 07:52:06.099: //31//MSW :/msw_recrd_open: rtspStream 0x4778D8D8 created,

status=RTSP_STATUS_SUCCESS, session_id=0x10 (16)

*Apr 13 07:52:06.103: //31//MSW :/msw_recog_open: AIS : Creating ASR AIS Backend record

*Apr 13 07:52:06.103: //-1//MSW :/msw_associate_call:

*Apr 13 07:52:06.103: msw_associate_call: callID=0x1F(31),

genericStream=0x477F0A48

*Apr 13 07:52:06.103: //31//MSW :/msw_synth_get_stream_state: genericStream 0x477F0A48 is in state MSW_S_IDLE

*Apr 13 07:52:06.103: //31//MSW :/msw_synth_start: current_stream_id=1, content 0x0, dynamicS 0x45E2CE78, current_state=MSW_S_IDLE

*Apr 13 07:52:06.103: //31//MSW :/msu_synth_partial_play: Media Stream URL

*Apr 13 07:52:36.127: //-1//MSW :/msw_synth_bargein:

*Apr 13 07:52:36.127: msw_synth_bargein: genericStream=0x477F0A48,

Hall of Fame Super Gold

Re: ITS with remote office

For some reason (busy ?) it fails. You can send all calls to operator directly even with a script anyway, just make a translation rule on the incoming dp. Or B-ACD should work.

New Member

Re: ITS with remote office

you are right b-acd worked fine.

Good day

140
Views
0
Helpful
7
Replies