Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

Bronze

Limit the number of PRI channels for 1 DN

Guys,

I've been asked to bring a site up  that, over the next 4-5 months, will handle a fairly heavy call volume. Is there any way I can limit the amount of concurrent calls to one DN? I don't want their number to overwhelm the rest of the system.

  This DN will be pointing to a Unity call handler to distribute the calls.

Call Manager 8.5

Unity Connection 8.5

Gateways are MGCP with 3 bonded PRI T1s

Thanks for any help you can give me!

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Silver

Limit the number of PRI channels for 1 DN

Assuming you have SCCP VM integration, the only issue I see with this is wasted voicemail ports, since they are licensed resources, you cannot share them for other calls. If you feel you have more than you need then you are OK.

Chris

8 REPLIES
Cisco Employee

Limit the number of PRI channels for 1 DN

Hi Gareth,

You can limit the number call by Maximum number calls setting in the Route point DN page.

Regards,

Gnan.

Bronze

Limit the number of PRI channels for 1 DN

Gnan,

That would work if I wasn't sending it over to Unity Connection to a call handler. Sadly, that's the way that they wand this to go.

Gareth

Green

Limit the number of PRI channels for 1 DN

Gareth,

If you could persuade others move the MGCP gateways to H323 (or SIP)

You can control the number of calls hitting VOIP dial peers etc

Something like this :-

!

dial-peer voice 1000 voip

description *** CUC CALL HANDLER PEER DN 1000 ***

preference 1

destination-pattern 1000

max-conn 50

voice-class codec 1

voice-class h323 1

session target ipv4:172.16.172.172

incoming called-number .

dtmf-relay h245-alphanumeric

ip qos dscp cs3 signaling

no vad

!

So that would yield 50 simultaneous calls with caller 51 hearing busy tone

MGCP is OK but it is not as granular as H323 or SIP

HTH

Alex

Please rate useful posts

Regards, Alex. Please rate useful posts.
Bronze

Limit the number of PRI channels for 1 DN

Thanks for the replies!

Just wanted to let you know that I've resolved it by cheating a little bit.

I went ahead and created a new voice profile with  a limited amount of voice ports (since it's being pushed to a call handler).

Anyone think of any problems with this?

Hall of Fame Super Silver

Limit the number of PRI channels for 1 DN

Assuming you have SCCP VM integration, the only issue I see with this is wasted voicemail ports, since they are licensed resources, you cannot share them for other calls. If you feel you have more than you need then you are OK.

Chris

Bronze

Limit the number of PRI channels for 1 DN

Chris,

I have plenty of licensed vm ports available. Not sure why we have as many as we do, to be honest!

Thanks for your reply.

Gareth

New Member

Limit the number of PRI channels for 1 DN

I have the same issue that I need to limit calls to a number, but they want it set at 18 in the day time and 5 at night. Is there a way to do it by time? either MGCP or H323. Or is this were a "time Period" would come in on CUCM.

Thanks

Cisco Employee

Limit the number of PRI channels for 1 DN

CUCM has no way to do this at all.

You would need to do this via TCL scripting on H323

HTH

java

If this helps, please rate

www.cisco.com/go/pdihelpdesk

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
661
Views
0
Helpful
8
Replies
CreatePlease login to create content