Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Meet-Me Number and Pattern

Hello,

I wanted to know if anyone has step-by-step directions on how to setup Meet-Me Number/Pattern on Cisco Callmanager 7.1.5.

Thank you

  • IP Telephony
2 ACCEPTED SOLUTIONS

Accepted Solutions
Hall of Fame Super Silver

Meet-Me Number and Pattern

Check you Administrator Guide for step by step directions, but there is very little to it, you go to Meet Me Patterns and define the range using default wildcards i.e. 55XX and assign partition to it. 

HTH,

Chris

Cisco Employee

Re: Meet-Me Number and Pattern

As Chris mentioned, there is nothing much but here you go with the document " Meet-Me Number/Pattern Configuration "

GP.

Pls rate helpful posts by clicking on stars below the post !!

15 REPLIES
Hall of Fame Super Silver

Meet-Me Number and Pattern

Check you Administrator Guide for step by step directions, but there is very little to it, you go to Meet Me Patterns and define the range using default wildcards i.e. 55XX and assign partition to it. 

HTH,

Chris

Cisco Employee

Re: Meet-Me Number and Pattern

As Chris mentioned, there is nothing much but here you go with the document " Meet-Me Number/Pattern Configuration "

GP.

Pls rate helpful posts by clicking on stars below the post !!

New Member

Re: Meet-Me Number and Pattern

Hello,

I have created a extension pool as per the link provided by Gajanan.  I have added the 1st number in the pool to a phone (7945), but I can't dial in from 2 different phones.  Am I doing something wrong or have I forgotten a step?

Hall of Fame Super Silver

Meet-Me Number and Pattern

What do you mean by:

I have added the 1st number in the pool to a phone (7945)

You define these ranges, then to start MeetMe you press MeetMe softkey on the phone and enter a number from this range, i.e. 7526 to start the MeetMe conference, then other calls dial 7526 to join it. Is this what you are doing?

Chris

New Member

Re: Meet-Me Number and Pattern

Chris,

I assigned 7526 to a phone. When I press the MeetMe softkey from another phone, I get 2 quick beeps. I dial the 7526 number and it connects to 7526. But when I dial 7526 from another phone, in order to answer it the 1st phone gets put on hold.

Thanks,

Hall of Fame Super Silver

Meet-Me Number and Pattern

You cannot assign overlapping DNs with MeetMe numbers to phones. You created a conflict. You can assign them as speed dials if you want, but not DNs.

HTH, please rate all useful posts!

Chris

Hall of Fame Super Red

Meet-Me Number and Pattern

Hi there,

Just to add a note to the great tips from Chris and Gajanan (+5)

- Remove 7526 from the 7945

- go to any phone press new call > MeetMe > 7526 (this will start the conference)

- from other phones dial 7526 and they will be added to meetme conference

Cheers!

Rob

"May your heart always be joyful And may your song always be sung May you stay forever young " - Dylan
New Member

Re: Meet-Me Number and Pattern

Thank you all for your help.  I also wanted to know if it is possible when someone joins there is a beep or announce a name?

Hall of Fame Super Red

Meet-Me Number and Pattern

Hi there,

I believe this is what you are looking for;

Service Parameters Configuration > Clusterwide Parameters (Feature - General)

Party Entrance Tone - True

Cheers!

Rob

"May your heart always be joyful And may your song always be sung May you stay forever young " - Dylan
685
Views
32
Helpful
15
Replies
This widget could not be displayed.