Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

MGCP debug error and CCM

when i run debug mgcp error - here is messages that drops

*Jun 19 07:50:26.236: mgcp_get_cac_params, Error Selecting codec

*Jun 19 07:50:34.432: mgcp_get_cac_params, Error Selecting codec

*Jun 19 07:50:36.796: mgcp_get_cac_params, Error Selecting codec

*Jun 19 07:50:38.784: mgcp_get_cac_params, Error Selecting codec

*Jun 19 07:50:39.408: mgcp_get_cac_params, Error Selecting codec

*Jun 19 07:50:45.184: mgcp_get_cac_params, Error Selecting codec

*Jun 19 07:50:46.148: mgcp_get_cac_params, Error Selecting codec

*Jun 19 07:50:59.884: mgcp_get_cac_params, Error Selecting codec

*Jun 19 07:51:00.308: mgcp_get_cac_params, Error Selecting codec

what is the problem ?

some-times GW balancing and registers to Subscriber and then goes Publisher.

5 REPLIES
New Member

Re: MGCP debug error and CCM

help!

New Member

Re: MGCP debug error and CCM

no answer?

Silver

Re: MGCP debug error and CCM

Would you please post your router config...at least the mgcp part of it. ALso if it is possible:

sh ccm

debug mgcp events

are you using PRI backhaul? post sh e1 contr.

New Member

Re: MGCP debug error and CCM

sh ccm

MGCP Domain Name: XXXXXX

Priority Status Host

============================================================

Primary Backup Ready XXXXXX

First Backup Registered XXXXXX

Second Backup None

Current active Call Manager: XXXXX

Backhaul/Redundant link port: 2428

Failover Interval: 30 seconds

Keepalive Interval: 15 seconds

Last keepalive sent: 10:48:50 UTC Jun 19 2008 (elapsed time: 00:01:28 )

Last MGCP traffic time: 10:50:01 UTC Jun 19 2008 (elapsed time: 00:00:17 )

Last failover time: 08:43:01 UTC Jun 19 2008 from (XXXXXXXX)

Last switchback time: 07:40:46 UTC Jun 19 2008 from (xxxxxxxx)

Switchback mode: Graceful

MGCP Fallback mode: Enabled/OFF

Last MGCP Fallback start time: 17:40:32 UTC Jun 14 2008

Last MGCP Fallback end time: 17:40:52 UTC Jun 14 2008

MGCP Download Tones: Disabled

Backhaul Link info:

Link Protocol: TCP

Remote Port Number: 2428

Remote IP Address: XXXXXXX

Current Link State: OPEN

Statistics:

Packets recvd: 3707

Recv failures: 0

Packets xmitted: 3771

Xmit failures: 0

PRI Ports being backhauled:

Slot 0, port 0

Slot 0, port 0

Configuration Auto-Download Information

=======================================

Current version-id: {XXXXXXXXXXXXXXXXXX}

Last config-downloaded:00:00:00

Current state: Waiting for commands

Configuration Download statistics:

Download Attempted : 80

Download Successful : 80

Download Failed : 0

Configuration Attempted : 6

Configuration Successful : 6

Configuration Failed(Parsing): 0

Configuration Failed(config) : 0

Last config download command: New Registration

Configuration Error History:

FAX mode: cisco

Silver

Re: MGCP debug error and CCM

Seems fine to me, please post your Router config, CCM version and debug mgcp events.

402
Views
0
Helpful
5
Replies
CreatePlease to create content