Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

MGCP E1 Port displays Amber

Dear All,

please help me on solving the below problem

E1 port on 2921 MGCP Gateway displays amber weither it's plugged or not. It is a new configuration

"show isdn status" shows Layer 1 status is SHUTDOWN

1 ACCEPTED SOLUTION

Accepted Solutions
VIP Purple

MGCP E1 Port displays Amber

Hi Kennedy,

Do not confuse with colours.

Kepping RJ-45 Jack towards Earth, from left towards right see 1, 2, 4 and 5 .

You can use unterminated cable at router end.

regds,

aman

48 REPLIES
VIP Purple

MGCP E1 Port displays Amber

Hi Kennedy,

can u share the show version , show diag and show license feature from the router?

show controllers e1 output from router and show isdn status

regds,

aman

MGCP E1 Port displays Amber

thanks for yor reply

moencovg#sh version

Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.2(4)M3, RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2013 by Cisco Systems, Inc.

Compiled Tue 26-Feb-13 03:42 by prod_rel_team

ROM: System Bootstrap, Version 15.0(1r)M16, RELEASE SOFTWARE (fc1)

moencovg uptime is 1 hour, 1 minute

System returned to ROM by reload at 12:28:05 UTC Wed Oct 9 2013

System image file is "flash0:c2900-universalk9-mz.SPA.152-4.M3.bin"

Last reload type: Normal Reload

Last reload reason: Reload Command

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

Cisco CISCO2921/K9 (revision 1.0) with 897024K/45056K bytes of memory.

Processor board ID FCZ172560ED

3 Gigabit Ethernet interfaces

20 Serial interfaces

1 terminal line

1 Channelized E1/PRI port

8 Voice FXO interfaces

4 Voice FXS interfaces

DRAM configuration is 64 bits wide with parity enabled.

255K bytes of non-volatile configuration memory.

250880K bytes of ATA System CompactFlash 0 (Read/Write)

License Info:

License UDI:

-------------------------------------------------

Device#   PID                   SN

-------------------------------------------------

*0        CISCO2921/K9          FCZ172560ED

Technology Package License Information for Module:'c2900'

-----------------------------------------------------------------

Technology    Technology-package           Technology-package

              Current       Type           Next reboot

------------------------------------------------------------------

ipbase        ipbasek9      Permanent      ipbasek9

security      None          None           None

uc            uck9          Permanent      uck9

data          None          None           None

Configuration register is 0x2102

###########################################

moencovg#show license

Index 1 Feature: ipbasek9

        Period left: Life time

        License Type: Permanent

        License State: Active, In Use

        License Count: Non-Counted

        License Priority: Medium

Index 2 Feature: securityk9

        Period left: Not Activated

        Period Used: 0  minute  0  second

        License Type: EvalRightToUse

        License State: Not in Use, EULA not accepted

        License Count: Non-Counted

        License Priority: None

Index 3 Feature: uck9

        Period left: Life time

        License Type: Permanent

        License State: Active, In Use

        License Count: Non-Counted

        License Priority: Medium

Index 4 Feature: datak9

        Period left: Not Activated

        Period Used: 0  minute  0  second

        License Type: EvalRightToUse

        License State: Not in Use, EULA not accepted

        License Count: Non-Counted

        License Priority: None

Index 5 Feature: gatekeeper

        Period left: Not Activated

        Period Used: 0  minute  0  second

        License Type: EvalRightToUse

        License State: Not in Use, EULA not accepted

        License Count: Non-Counted

        License Priority: None

Index 6 Feature: SSL_VPN

        Period left: Not Activated

        Period Used: 0  minute  0  second

        License Type: EvalRightToUse

        License State: Not in Use, EULA not accepted

        License Count: 0/0  (In-use/Violation)

        License Priority: None

Index 7 Feature: ios-ips-update

        Period left: Not Activated

        Period Used: 0  minute  0  second

        License Type: EvalRightToUse

        License State: Not in Use, EULA not accepted

        License Count: Non-Counted

        License Priority: None

Index 8 Feature: SNASw

        Period left: Not Activated

        Period Used: 0  minute  0  second

        License Type: EvalRightToUse

        License State: Not in Use, EULA not accepted

        License Count: Non-Counted

        License Priority: None

Index 9 Feature: hseck9

Index 10 Feature: cme-srst

        Period left: Not Activated

        Period Used: 0  minute  0  second

        License Type: EvalRightToUse

        License State: Not in Use, EULA not accepted

        License Count: 0/0  (In-use/Violation)

        License Priority: None

Index 11 Feature: WAAS_Express

        Period left: Not Activated

        Period Used: 0  minute  0  second

        License Type: EvalRightToUse

        License State: Not in Use, EULA not accepted

        License Count: Non-Counted

        License Priority: None

Index 12 Feature: UCVideo

        Period left: Not Activated

        Period Used: 0  minute  0  second

        License Type: EvalRightToUse

        License State: Not in Use, EULA not accepted

        License Count: Non-Counted

        License Priority: None

########################################

moencovg#sh isdn status

Global ISDN Switchtype = primary-4ess

%Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 0. Layer 3 output may not apply

ISDN Serial0/0/0:15 interface

        dsl 0, interface ISDN Switchtype = primary-net5

        L2 Protocol = Q.921 0x0000  L3 Protocol(s) = CCM MANAGER 0x0003

    Layer 1 Status:

        DEACTIVATED

    Layer 2 Status:

        TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED

    Layer 3 Status:

        0 Active Layer 3 Call(s)

    Active dsl 0 CCBs = 0

    The Free Channel Mask:  0x00000000

    Number of L2 Discards = 0, L2 Session ID = 32

    Total Allocated ISDN CCBs = 0

################################################

moencovg#sh controllers e1

E1 0/0/0 is down.

  Applique type is Channelized E1 - balanced

  Transmitter is sending remote alarm.

  Receiver has loss of signal.

  alarm-trigger is not set

  Version info FPGA Rev: 08121917, FPGA Type: PRK1

  Framing is CRC4, Line Code is HDB3, Clock Source is Line.

  International Bit: 1, National Bits: 11111

  Data in current interval (844 seconds elapsed):

     0 Line Code Violations, 0 Path Code Violations

     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 844 Unavail Secs

  Total Data (last 5 15 minute intervals):

     5 Line Code Violations, 8 Path Code Violations,

     23 Slip Secs, 0 Fr Loss Secs, 4 Line Err Secs, 0 Degraded Mins,

     24 Errored Secs, 1 Bursty Err Secs, 0 Severely Err Secs, 4201 Unavail Secs

#####################################################

C2921 Mother board 3GE, integrated VPN and 4W Port adapter, 16 ports

        Port adapter is analyzed

        Port adapter insertion time 01:06:07 ago

        EEPROM contents at hardware discovery:

        PCB Serial Number        : FOC17147YQT

        Hardware Revision        : 1.0

        Part Number              : 73-11835-11

        Top Assy. Part Number    : 800-30794-07

        Board Revision           : A0

        Deviation Number         : 130603

        Fab Version              : 03

        Product (FRU) Number     : CISCO2921/K9

        Version Identifier       : V08

        CLEI Code                : CMMHS10ARB

        Processor type           : C2

        Chassis Serial Number    : FCZ172560ED

        Chassis MAC Address      : bc16.65e6.8b20

        MAC Address block size   : 80

        Manufacturing Test Data  : 00 00 00 00 00 00 00 00

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF C1 8B 46 4F 43 31 37 31 34 37 59 51 54 40

          0x10: 06 16 41 01 00 82 49 2E 3B 0B C0 46 03 20 00 78

          0x20: 4A 07 42 41 30 88 00 01 FE 2B 02 03 CB 8C 43 49

          0x30: 53 43 4F 32 39 32 31 2F 4B 39 89 56 30 38 20 D9

          0x40: 04 40 C1 CB C2 C6 8A 43 4D 4D 48 53 31 30 41 52

          0x50: 42 09 C2 C2 8B 46 43 5A 31 37 32 35 36 30 45 44

          0x60: C3 06 BC 16 65 E6 8B 20 43 00 50 C4 08 00 00 00

          0x70: 00 00 00 00 00 F3 00 03 40 01 63 FF FF FF FF FF

          0x80: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x90: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0xA0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0xB0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0xC0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0xD0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0xE0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0xF0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

        Internal Power Supply information

        Top Assy. Part Number    : 341-0226-03

        Deviation Number         : 0

        PCB Serial Number        : QCS1710H1CB

        RMA Test History         : 00

        RMA Number               : 0-0-0-0

        RMA History              : 00

        Version Identifier       : V03

        Product (FRU) Number     : PWR-2921-51-AC

        CLEI Code                : 0000000000

        Board Revision           : A0

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF 40 05 E2 DF 45 01 55 00 E2 03 88 00 00 00

          0x10: 00 C1 8B 51 43 53 31 37 31 30 48 31 43 42 03 00

          0x20: 81 00 00 00 00 04 00 89 56 30 33 20 CB 8E 50 57

          0x30: 52 2D 32 39 32 31 2D 35 31 2D 41 43 C6 8A 30 30

          0x40: 30 30 30 30 30 30 30 30 F3 00 59 41 01 22 42 00

          0x50: 05 F8 00 50 01 F4 14 41 02 EE 16 F0 03 E8 18 C9

          0x60: 04 E2 1A 76 05 DC 1B 91 06 D6 1C 78 07 D0 1D 10

          0x70: 08 CA 1D 9E 09 C4 1E 6D 0A BE 1E A8 0B B8 1F 5E

          0x80: 0D AC 20 FB 0F A0 21 18 11 94 21 64 13 88 21 71

          0x90: 17 70 21 9F 1B 58 21 96 1F 40 21 6D 23 28 21 62

          0xA0: 27 10 21 5A 42 41 30 FF FF FF FF FF FF FF FF FF

          0xB0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0xC0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0xD0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0xE0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0xF0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

        Redundant Power Supply Adapter information

        PCB Serial Number        : FOC17191VSV

Hardware Revision        : 1.0

        Part Number              : 73-12224-03

        Top Assy. Part Number    : 800-31691-01

        Board Revision           : E0

        Deviation Number         : 135137

        Fab Version              : 03

        Product (FRU) Number     : RPS-ADPTR-2921-51

        Version Identifier       : V01

        CLEI Code                : COPQAA2JAA

        Manufacturing Test Data  : 00 00 00 00 00 00 00 00

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF C1 8B 46 4F 43 31 37 31 39 31 56 53 56 40

          0x10: 06 1A 41 01 00 82 49 2F C0 03 C0 46 03 20 00 7B

          0x20: CB 01 42 45 30 88 00 02 0F E1 02 03 CB 91 52 50

          0x30: 53 2D 41 44 50 54 52 2D 32 39 32 31 2D 35 31 89

          0x40: 56 30 31 20 C6 8A 43 4F 50 51 41 41 32 4A 41 41

          0x50: C4 08 00 00 00 00 00 00 00 00 FF FF FF FF FF FF

        PVDM Slot 0:

        32-channel (G.711) Voice/Fax PVDM3 DSP DIMM PVDM daughter card

        Hardware Revision        : 1.0

        Part Number              : 73-11577-03

        Board Revision           : D0

        Deviation Number         : 0

        Fab Version              : 03

        PCB Serial Number        : FOC17121MUM

        RMA Test History         : 00

        RMA Number               : 0-0-0-0

        RMA History              : 00

        Processor type           : 00

        Product (FRU) Number     : PVDM3-32

        Version Identifier       : V01

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF 40 05 D9 41 01 00 82 49 2D 39 03 42 44 30

          0x10: 88 00 00 00 00 02 03 C1 8B 46 4F 43 31 37 31 32

          0x20: 31 4D 55 4D 03 00 81 00 00 00 00 04 00 09 00 CB

          0x30: 8F 50 56 44 4D 33 2D 33 32 20 20 20 20 20 20 20

          0x40: 89 56 30 31 20 D9 02 40 C1 FF FF FF FF FF FF FF

          0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

        WIC Slot 0:

        VWIC3-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1

Hardware Revision        : 1.0

        Top Assy. Part Number    : 800-34657-01

        Part Number              : 73-13419-01

        Board Revision           : B0

        Deviation Number         : 0

        Fab Version              : 05

        PCB Serial Number        : FOC17224W9T

        Version Identifier       : V01

        Product (FRU) Number     : VWIC3-1MFT-T1/E1

        CLEI Code                : COUIA7PCAA

        RMA Test History         : 00

        RMA Number               : 0-0-0-0

        RMA History              : 00

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF 40 06 ED 41 01 00 C0 46 03 20 00 87 61 01

          0x10: 82 49 34 6B 01 42 42 30 88 00 00 00 00 02 05 C1

          0x20: 8B 46 4F 43 31 37 32 32 34 57 39 54 89 56 30 31

          0x30: 20 CB 90 56 57 49 43 33 2D 31 4D 46 54 2D 54 31

          0x40: 2F 45 31 C6 8A 43 4F 55 49 41 37 50 43 41 41 03

          0x50: 00 81 00 00 00 00 04 00 D9 03 40 C1 CB FF FF FF

          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

        WIC Slot 1:

        3rd generation - FXS DID Voice daughter card (4 port)

        Hardware Revision        : 1.0

        Top Assy. Part Number    : 800-33583-01

        Board Revision           : E0

        Deviation Number         : 0

        Fab Version              : 07

        PCB Serial Number        : FOC171787U4

        RMA Test History         : 00

        RMA Number               : 0-0-0-0

        RMA History              : 00

        Product (FRU) Number     : VIC3-4FXS/DID

        Version Identifier       : V03

        CLEI Code                : IPUIA6JRAC

        Longitudinal Calibration : 01 10 10 63 6B 10 10 9B

                                   B7 10 10 96 6D 10 10 92

                                   AE

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF 40 05 1B 41 01 00 C0 46 03 20 00 83 2F 01

          0x10: 42 45 30 88 00 00 00 00 02 07 C1 8B 46 4F 43 31

          0x20: 37 31 37 38 37 55 34 03 00 81 00 00 00 00 04 00

          0x30: CB 8D 56 49 43 33 2D 34 46 58 53 2F 44 49 44 89

          0x40: 56 30 33 20 D9 02 40 C1 C6 8A 49 50 55 49 41 36

          0x50: 4A 52 41 43 D3 11 01 10 10 63 6B 10 10 9B B7 10

          0x60: 10 96 6D 10 10 92 AE FF FF FF FF FF FF FF FF FF

          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

        WIC Slot 2:

        2nd generation - FXO Voice daughter card (4 port)

        Hardware Revision        : 5.0

        Top Assy. Part Number    : 800-33585-01

        Board Revision           : E0

        Deviation Number         : 0-0

        Fab Version              : 04

        PCB Serial Number        : FOC1704725W

        RMA Test History         : 00

        RMA Number               : 0-0-0-0

        RMA History              : 00

        Product (FRU) Number     : VIC2-4FXO

        Version Identifier       : V04

        CLEI Code                : CNUIAXJAAC

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF 40 00 4C 41 05 00 C0 46 03 20 00 83 31 01

0x10: 42 45 30 80 00 00 00 00 02 04 C1 8B 46 4F 43 31

          0x20: 37 30 34 37 32 35 57 03 00 81 00 00 00 00 04 00

          0x30: CB 89 56 49 43 32 2D 34 46 58 4F 89 56 30 34 20

          0x40: C6 8A 43 4E 55 49 41 58 4A 41 41 43 FF FF FF FF

          0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

        WIC Slot 3:

        2nd generation - FXO Voice daughter card (4 port)

        Hardware Revision        : 5.0

        Top Assy. Part Number    : 800-33585-01

        Board Revision           : E0

        Deviation Number         : 0-0

        Fab Version              : 04

        PCB Serial Number        : FOC17036LHL

        RMA Test History         : 00

        RMA Number               : 0-0-0-0

        RMA History              : 00

        Product (FRU) Number     : VIC2-4FXO

        Version Identifier       : V04

        CLEI Code                : CNUIAXJAAC

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF 40 00 4C 41 05 00 C0 46 03 20 00 83 31 01

          0x10: 42 45 30 80 00 00 00 00 02 04 C1 8B 46 4F 43 31

          0x20: 37 30 33 36 4C 48 4C 03 00 81 00 00 00 00 04 00

          0x30: CB 89 56 49 43 32 2D 34 46 58 4F 89 56 30 34 20

          0x40: C6 8A 43 4E 55 49 41 58 4A 41 41 43 FF FF FF FF

          0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

Embedded Service Engine 0/0 :

  Total platform memory : 524288K bytes

  Total 2nd core memory : 0K bytes

  Start of physical address for 2nd core : 0x80000000

  Virtual address start of 2nd core memory : 0x0 - 0x0

  2nd core configured disabled

  L2 cache ways for 2nd core : 0

#######################3

best regards

Kennedy

MGCP E1 Port displays Amber

now I've connected the service provider E1 cable and on cucm E1 port displays "Rejected" in addition to that on the gate way the show isdn status command shows Layer 1 Deactivated

VIP Purple

MGCP E1 Port displays Amber

Hi Kennedy,

Is your E1 UP? Have u configured MGCP or H.323.?

Can u try physically shorting the pairs 1 with 4 and 2 with 5 ? just to check whether E1 port is perferect or not.

regds,

aman

MGCP E1 Port displays Amber

I've configured my E1 for MGCP,

My E1 is down but when i did i loopback diag it goes up

my connection to the the SP modem is, i just use a fabricated straight through patch cord by bcuting white green, green, white orange and orange. the connect white green with orange, green with white orange and vice versa

VIP Purple

MGCP E1 Port displays Amber

Hi,

Try changing the framing crc-4 to no-crc4.

if it still does not come UP, try swapping the pairs.

regds,

aman

MGCP E1 Port displays Amber

Dear Aman,

nothing changed but when i reload the router i saw the below error lines

call manager backhaul registration failed

unable to setup isdn layer 3 protocol on interface

one thing that make confuse is the the E1 port dispays Amber without pluging any cable. can you tell me what the reason is ?

best regards

Kennedy

VIP Purple

MGCP E1 Port displays Amber

Hi Kennedy,

can u share the router config?

regds,

aman

MGCP E1 Port displays Amber

Dear Aman,

please see the router config below

moencovg#sh run

Building configuration...

Current configuration : 7517 bytes

!

! Last configuration change at 16:05:28 UTC Wed Oct 9 2013 by admin

version 15.2

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname moencovg

!

boot-start-marker

boot-end-marker

!

!

card type e1 0 0

logging buffered 51200 warnings

enable secret 4 c5LFTnp3A5C3Ds2sCA3PU0Csl6Q1V1MpHyKNktEi5tI

!

no aaa new-model

network-clock-participate wic 0

!

ip cef

!

!

!

ip dhcp excluded-address 10.10.10.1

!

!

!

ip domain name moenco.corp

ip name-server 172.20.0.23

no ipv6 cef

multilink bundle-name authenticated

!

!

!

!

isdn switch-type primary-4ess

!

!

crypto pki trustpoint TP-self-signed-3990007969

enrollment selfsigned

subject-name cn=IOS-Self-Signed-Certificate-3990007969

revocation-check none

rsakeypair TP-self-signed-3990007969

!

!

crypto pki certificate chain TP-self-signed-3990007969

certificate self-signed 01

  3082022B 30820194 A0030201 02020101 300D0609 2A864886 F70D0101 05050030

  31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274

  69666963 6174652D 33393930 30303739 3639301E 170D3133 30363139 30373030

  30385A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649

  4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D33 39393030

  30373936 3930819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281

  8100E6F7 448AA926 A7D8AAD8 D3488CFF F2928A99 E7A427F1 6EFEC5F6 0706E9B8

  505657CE 98499BD6 9D7D21AF 55718077 077128E1 21C8DFD4 CD1E9F79 D161DEBC

  D107795F BDB1E908 582C3140 A4F1FBC2 00C75850 28A3309F 84F229D0 95BD7ADE

  121CF969 275BF813 048504D4 9D12A4B7 2A724A78 CF02A15F 29927BC8 39F5482C

  F8130203 010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603

  551D2304 18301680 14B41221 0B2A24EC A4EB7BC8 74DD5344 87E4A0BF BD301D06

  03551D0E 04160414 B412210B 2A24ECA4 EB7BC874 DD534487 E4A0BFBD 300D0609

  2A864886 F70D0101 05050003 81810072 33910E76 9A03BBBF FDCFD9F5 C384A55B

  D6D7E295 03AD17F8 4F7AF038 5A694E57 8A8858C4 61F10181 28C7CD37 FDAD2D1C

  56CAD1D6 31AAE479 773A5807 61C136D4 EE6646A9 D7153DE9 DADB4414 68DAC5D9

  3DDA1AED 6712F942 4000B818 D7424520 CBBCF430 1748A277 C1AB92C3 08905875

  430F1134 6C192164 81BD656D 398B82

        quit

voice-card 0

!

!

!

!

!

!

!

!

license udi pid CISCO2921/K9 sn FCZ172560ED

hw-module pvdm 0/0

!

!

!

username admin privilege 15 password 0 p@ssw0rd

!

redundancy

!

!

controller E1 0/0/0

pri-group timeslots 1-20 service mgcp

!

!

!

!

!

interface Embedded-Service-Engine0/0

no ip address

shutdown

!

interface GigabitEthernet0/0

description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE 0/0$

ip address 172.20.0.49 255.255.255.0

duplex auto

speed auto

!

interface GigabitEthernet0/1

no ip address

shutdown

duplex auto

speed auto

!

interface GigabitEthernet0/2

no ip address

shutdown

duplex auto

speed auto

!

interface Serial0/0/0:15

no ip address

encapsulation hdlc

isdn switch-type primary-net5

isdn incoming-voice voice

isdn bind-l3 ccm-manager

no cdp enable

!

ip default-gateway 172.20.0.11

ip forward-protocol nd

!

ip http server

ip http access-class 23

ip http authentication local

ip http secure-server

ip http timeout-policy idle 60 life 86400 requests 10000

!

!

access-list 23 permit 10.10.10.0 0.0.0.7

!

!

!

control-plane

!

!

voice-port 0/0/0:15

!

voice-port 0/1/0

!

voice-port 0/1/1

!

voice-port 0/1/2

!

voice-port 0/1/3

!

voice-port 0/2/0

timing hookflash-out 50

timing guard-out 1000

!

voice-port 0/2/1

timing hookflash-out 50

timing guard-out 1000

!

voice-port 0/2/2

timing hookflash-out 50

timing guard-out 1000

!

voice-port 0/2/3

timing hookflash-out 50

timing guard-out 1000

!

voice-port 0/3/0

timing hookflash-out 50

timing guard-out 1000

!

voice-port 0/3/1

timing hookflash-out 50

timing guard-out 1000

!

voice-port 0/3/2

timing hookflash-out 50

timing guard-out 1000

!

voice-port 0/3/3

timing hookflash-out 50

timing guard-out 1000

!

!

!

!

ccm-manager mgcp

no ccm-manager fax protocol cisco

ccm-manager music-on-hold

ccm-manager config server 172.20.0.41

ccm-manager config

!

mgcp

mgcp call-agent 172.20.0.41 2427 service-type mgcp version 0.1

mgcp rtp unreachable timeout 1000 action notify

mgcp modem passthrough voip mode nse

mgcp package-capability rtp-package

mgcp package-capability sst-package

mgcp package-capability pre-package

no mgcp package-capability res-package

no mgcp timer receive-rtcp

mgcp sdp simple

mgcp fax t38 inhibit

!

mgcp profile default

!

!

dial-peer voice 999021 pots

service mgcpapp

port 0/2/1

!

dial-peer voice 999022 pots

service mgcpapp

port 0/2/2

!

dial-peer voice 999020 pots

service mgcpapp

port 0/2/0

!

dial-peer voice 999023 pots

service mgcpapp

port 0/2/3

!

dial-peer voice 999030 pots

service mgcpapp

port 0/3/0

!

dial-peer voice 999031 pots

service mgcpapp

port 0/3/1

!

dial-peer voice 999032 pots

service mgcpapp

port 0/3/2

!

dial-peer voice 999033 pots

service mgcpapp

port 0/3/3

!

dial-peer voice 999010 pots

service mgcpapp

port 0/1/0

!

dial-peer voice 999011 pots

service mgcpapp

port 0/1/1

!

dial-peer voice 999012 pots

service mgcpapp

port 0/1/2

!

dial-peer voice 999013 pots

service mgcpapp

port 0/1/3

!

!

!

!

gatekeeper

shutdown

!

!

banner exec ^C

% Password expiration warning.

-----------------------------------------------------------------------

Cisco Configuration Professional (Cisco CP) is installed on this device

and it provides the default username "cisco" for  one-time use. If you have

already used the username "cisco" to login to the router and your IOS image

supports the "one-time" user option, then this username has already expired.

You will not be able to login to the router with this username after you exit

this session.

It is strongly suggested that you create a new username with a privilege level

of 15 using the following command.

username privilege 15 secret 0

Replace and with the username and password you want to

use.

-----------------------------------------------------------------------

^C

banner login ^C

-----------------------------------------------------------------------

Cisco Configuration Professional (Cisco CP) is installed on this device.

This feature requires the one-time use of the username "cisco" with the

password "cisco". These default credentials have a privilege level of 15.

YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE  PUBLICLY-KNOWN

CREDENTIALS

Here are the Cisco IOS commands.

username   privilege 15 secret 0

no username cisco

Replace and with the username and password you want

to use.

IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE

TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.

For more information about Cisco CP please follow the instructions in the

QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp

-----------------------------------------------------------------------

^C

!

line con 0

login local

line aux 0

line 2

no activation-character

no exec

transport preferred none

transport input all

transport output pad telnet rlogin lapb-ta mop udptn v120 ssh

stopbits 1

line vty 0 4

access-class 23 in

privilege level 15

password p@ssw0rd

login

transport input telnet ssh

line vty 5 10

access-class 23 in

privilege level 15

password p@ssw0rd

login local

transport input telnet ssh

line vty 11 15

access-class 23 in

privilege level 15

login local

transport input telnet ssh

!

scheduler allocate 20000 1000

!

end

best regards

Kennedy

MGCP E1 Port displays Amber

Dear Aman,

FYI: when i restart the cucm i can see the E1 is registered to the cucm but i make refresh to the cucm interface it immediately changed to unregistered.

best regards

Kennedy

VIP Purple

MGCP E1 Port displays Amber

Hi,

Try entering the below command and save it.then, check.

regds,

aman

VIP Purple

MGCP E1 Port displays Amber

Hi,

Can u try removing the command isdn bind-l3 ccm-manager under serial interface and check?

use shut and no shut?

if possible , share ccm-manager from router.

regds,

aman

MGCP E1 Port displays Amber

Dear Aman,

Ive removed the command isdn bind-l3 ccm-manager under serial interface but nothing changed.

please see below the ccm-manager config

moencovg#sh ccm-manager

MGCP Domain Name: moencovg.moenco.corp

Priority        Status                   Host

============================================================

Primary         Registered               172.20.0.41

First Backup    None

Second Backup   None

Current active Call Manager:    172.20.0.41

Backhaul/Redundant link port:   2428

Failover Interval:              30 seconds

Keepalive Interval:             15 seconds

Last keepalive sent:            16:54:32 UTC Oct 9 2013 (elapsed time: 00:00:40)

Last MGCP traffic time:         16:55:03 UTC Oct 9 2013 (elapsed time: 00:00:10)

Last failover time:             None

Last switchback time:           None

Switchback mode:                Graceful

MGCP Fallback mode:             Not Selected

Last MGCP Fallback start time:  None

Last MGCP Fallback end time:    None

MGCP Download Tones:            Disabled

TFTP retry count to shut Ports: 2

Backhaul Link info:

    Link Protocol:      TCP

    Remote Port Number: 2428

    Remote IP Address:  172.20.0.41

    Current Link State: OPEN

    Statistics:

        Packets recvd:   2

        Recv failures:   0

        Packets xmitted: 3

        Xmit failures:   0

    PRI Ports being backhauled:

        Slot 0, VIC 0, port 0

Configuration Auto-Download Information

=======================================

Current version-id: 1381311358-03020a20-33de-41c4-bfd5-8959b09b0e45

Last config-downloaded:00:00:00

Current state: Waiting for commands

Configuration Download statistics:

        Download Attempted             : 1

          Download Successful          : 1

          Download Failed              : 0

          TFTP Download Failed         : 0

        Configuration Attempted        : 1

          Configuration Successful     : 1

          Configuration Failed(Parsing): 0

          Configuration Failed(config) : 0

Last config download command: New Registration

FAX mode: disable

Configuration Error History:

moencovg#

#################################

now it's 8 PM i'm leaving the project site but i can get you back after 30 minutes fro home

best regards

Kennedy

VIP Purple

MGCP E1 Port displays Amber

Hi Kennedy,

Save the config and just reload the router ?

regds,

aman

MGCP E1 Port displays Amber

Dear Aman,

I've saved the config and did a reload

MGCP E1 Port displays Amber

Hi

1- on gateway

no ccm-manager config server 172.20.0.41   

no ccm-manager config      /you have to edit setting on your config on your CUCM , so better not use these commands?

!

mgcp

mgcp call-agent 172.20.0.41 2427 service-type mgcp version 0.1

mgcp dtmf-relay voip codec all mode out-of -band

mgcp bind control sourec-interface ( G0/0) interface which can be reachble to your CUCM

mgcp bind medial sourec-interface ( G0/0) interface which can be reachble to your CUCM

2- on the CUCM the name of your router should be as the below:-

moencovg.moenco.corp

this the same name of your router.

Thank you

please rate all useful information


Re:MGCP E1 Port displays Amber

Hi

Please find the below link for the problem for your Layer 1 which is shown deactivated.

http://www.cisco.com/en/US/tech/tk801/tk379/technologies_tech_note09186a0080094b76.shtml

Thank you

please rate all useful information

MGCP E1 Port displays Amber

Hi,

that was just for few seconds it turned back to SHUTDOWN

best regards

kennedy

VIP Super Bronze

Re:MGCP E1 Port displays Amber

You need to check your cabling. Your e1 controller has alarms on it. I suggest you sort that out first.

Second ensure that your mgcp domain configured on cucm is the same as the mgcp domain name that you see when you do a show ccm-manager


Sent from Cisco Technical Support Android App

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"

MGCP E1 Port displays Amber

Hi,

the e1 is displaying amber without any cable being pluged & that's why I'm confused. can you tell me what the reason is ?

best regards

Kennedy

VIP Super Bronze

MGCP E1 Port displays Amber

The e1 will display amber without any active circuit connection. This is normal. When you plug a cable to your e1 and you have an active connection to your telco, then the light changes from amber to green. If you plug a cable in and the light still shows as amber, then there is a problem either with the cable, your card , framing configuraion or your telco has not activated your line..

Dont waste your time reloading and re-configuring..You need to focus on bringing up your layer 1...which invlolves cabling, framing configuration etc

Please rate all useful posts

"opportunity is a haughty goddess who waste no time with those who are unprepared"

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"

MGCP E1 Port displays Amber

Hi

+5 for MR.Aokanlawon , please check your cable . When you get on layer 1 activated , so we can easily troubleshoot all configuration for mgcp if you will fix any other problem.

Thank you

please rate all useful information

MGCP E1 Port displays Amber

Hi

after plugging the telco cable and restarting the cucm i can see the E1 is registered to the cucm  but when i make refresh to the cucm interface it immediately changed to  unregistered. why is that ?

best regards

Kennedy

VIP Super Bronze

MGCP E1 Port displays Amber

Please send the ff:

sh isdn status

show ccm-manager

Please rate all useful posts

"opportunity is a haughty goddess who waste no time with those who are unprepared"

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"

MGCP E1 Port displays Amber

Hi,

My local time 4:50 PM & I'm not @ the project site but i've taken some of the configurations. there are also other configurations those i've uploaded in this forum earlier.

moencovg#sh isdn status

Global ISDN Switchtype = primary-4ess

%Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 0. Layer 3 output may not apply

ISDN Serial0/0/0:15 interface

        dsl 0, interface ISDN Switchtype = primary-net5

        L2 Protocol = Q.921 0x0000  L3 Protocol(s) = CCM MANAGER 0x0003

    Layer 1 Status:

        DEACTIVATED #currently it is shutdown#

    Layer 2 Status:

        TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED

    Layer 3 Status:

        0 Active Layer 3 Call(s)

    Active dsl 0 CCBs = 0

    The Free Channel Mask:  0x00000000

    Number of L2 Discards = 0, L2 Session ID = 32

    Total Allocated ISDN CCBs = 0

#################################################

moencovg#sh ccm-manager

MGCP Domain Name: moencovg.moenco.corp

Priority        Status                   Host

============================================================

Primary         Registered               172.20.0.41

First Backup    None

Second Backup   None

Current active Call Manager:    172.20.0.41

Backhaul/Redundant link port:   2428

Failover Interval:              30 seconds

Keepalive Interval:             15 seconds

Last keepalive sent:            16:54:32 UTC Oct 9 2013 (elapsed time: 00:00:40)

Last MGCP traffic time:         16:55:03 UTC Oct 9 2013 (elapsed time: 00:00:10)

Last failover time:             None

Last switchback time:           None

Switchback mode:                Graceful

MGCP Fallback mode:             Not Selected

Last MGCP Fallback start time:  None

Last MGCP Fallback end time:    None

MGCP Download Tones:            Disabled

TFTP retry count to shut Ports: 2

Backhaul Link info:

    Link Protocol:      TCP

    Remote Port Number: 2428

    Remote IP Address:  172.20.0.41

    Current Link State: OPEN

    Statistics:

        Packets recvd:   2

        Recv failures:   0

        Packets xmitted: 3

        Xmit failures:   0

    PRI Ports being backhauled:

        Slot 0, VIC 0, port 0

Configuration Auto-Download Information

=======================================

Current version-id: 1381311358-03020a20-33de-41c4-bfd5-8959b09b0e45

Last config-downloaded:00:00:00

Current state: Waiting for commands

Configuration Download statistics:

        Download Attempted             : 1

          Download Successful          : 1

          Download Failed              : 0

          TFTP Download Failed         : 0

        Configuration Attempted        : 1

          Configuration Successful     : 1

          Configuration Failed(Parsing): 0

          Configuration Failed(config) : 0

Last config download command: New Registration

FAX mode: disable

Configuration Error History:

moencovg#

Best Regards

Kennedy

VIP Super Bronze

MGCP E1 Port displays Amber

When you get back to site..please send the output that I asked for..

Why is your e1 in a shut down state..try and enable it..

conf t

controller e1 0/0/0

no shut

Please rate all useful posts

"opportunity is a haughty goddess who waste no time with those who are unprepared"

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"

MGCP E1 Port displays Amber

Hi,

I've tried to do that many times but it couldn't came up and for how long hours are you available from now on ?

best regards

Kennedy

VIP Super Bronze

MGCP E1 Port displays Amber

Do you have another e1 card? If you I suggest you swap this one out and put that in..Do you also know if this line has been actuvated by your telco?

I am available for the next 11/2 hrs

Please rate all useful posts

"opportunity is a haughty goddess who waste no time with those who are unprepared"

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"

MGCP E1 Port displays Amber

Hi,

i don't have another e1 card and the telco already activated the line.

FYI when i did a loopback diag my controller e1 gets up why is that ?

is there any specific framing that i should configure ?

best regards

Kennedy

900
Views
5
Helpful
48
Replies
CreatePlease to create content