Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

MGCP Gateway fallback with CUCM 7

I have a router 2811  ios version 12.4(22) and a Cucm7.

I want to setup the 2811 gateway with a fxo active port to act as a  fallback function for the Cucm.

I have setup the following commands:

-from the cucm /srst, add new- router`s ip and name, port 2000,

-in the device pool i have setup at srst the router`s name,

-in the gateway i have setup the router as new gateway, configured as mgcp, i have entered at the domain name tab: "router`s name".domain.com

- i have selected the subunit 0 in my case with the 2fxo, controlled as mgcp (AALN/S0/SU0/0@"router name''.domain.com)

On the router i configured :

R(config)#ccm-manager fallback

R(config)#application
R(config-app)#global
R(config-app-global)#service alternate Default
Router(config)# call-manager-fallback
Router(config-cm-fallback)# keepalive 60
Router(config)# call-manager-fallback
Router(config-cm-fallback)# ip source-address 10.x.x.x port 2002 strict-match  (10.x.x.x - router`s address)
Router(config-cm-fallback)# max-dn 24 dual-line preference 1
Router(config-cm-fallback)# max-ephones 24
Router(config-cm-fallback)# limit-dn 7911 2
If i type
cme#show ccm-manager fallback-mgcp
% Call Manager Application is not enabled

What am i missing here ...

4 REPLIES
VIP Super Bronze

Re: MGCP Gateway fallback with CUCM 7

Looks like you are missing the command

ccm-manager fallback-mgcp

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
New Member

Re: MGCP Gateway fallback with CUCM 7

Nope, i have typed id. I just forgot to mention it.

I have followed this steps...

http://www.cisco.com/en/US/docs/voice_ip_comm/cusrst/admin/srst/configuration/guide/SRST_SysAdmin.pdf

1. enable
2. configure terminal
3. ccm-manager fallback-mgcp
4. call application alternate [application-name]
or
service [alternate | default] service-name location
5. exit

New Member

Re: MGCP Gateway fallback with CUCM 7

I have made the router to register with the CUCM, this is a part of the router`s config.

ccm-manager fallback-mgcp
ccm-manager mgcp
ccm-manager fax protocol cisco
ccm-manager music-on-hold
ccm-manager config server 10.X.X>X
ccm-manager config
!
mgcp
mgcp call-agent 10.X.X.X service-type mgcp version 0.1
mgcp rtp unreachable timeout 1000 action notify
mgcp modem passthrough voip mode nse
mgcp package-capability rtp-package
mgcp package-capability sst-package
mgcp package-capability pre-package
no mgcp package-capability res-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp fax t38 ecm
mgcp rtp payload-type g726r16 static
!
mgcp profile default

The only problem that i have now is that ephone-dn assigned.

router#$CA35.C7D4 TCP socket:[2] activeLine:0 REGISTERED in SCCP ver 19/9
ephone-1[0] Mac:001F.CA35.C7D4 TCP socket:[2] activeLine:0 REGISTERED in SCCP ve       ^r 19/9

On show-ephone command, the available line doesn`t appear

ephone-1[0] Mac:0xxxxxxxxxx TCP socket:[2] activeLine:0 whisperLine:0  REGISTERED in SCCP ver 19/97 max_streams=5
mediaActive:0  whisper_mediaActive:0 startMedia:0 offhook:0 ringing:0 reset:0  reset_sent:0 paging 0 debug:1 caps:11
IP:1XXXXXX* 36015 7961   keepalive 38 max_line 34


I don`t have dhcp created, i have static ip.

Does anyone know why the phone failed to get a ephone-dn?

New Member

Re: MGCP Gateway fallback with CUCM 7

Guys i`ve figer it out what it was. It was the damned 7911 phone. I think it was a firmware issue.

I`ve tested on my ip comunicator phone and it worked perfectly

2108
Views
0
Helpful
4
Replies