Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Users might experience few discrepancies in Search results. We are working on this on our side. We apologize for the inconvenience it may have caused.

MGCP gateway port rejected

Hello, I have a 2851 with a EVM-HD-8FXS/DID card configured as a MGCP gateway in a CCM 5.1 cluster environment. All ports appear as registered except the first one which appears as rejected. The config is the same than the others ports. I have reloaded the gateway the problem has not been solved. I'm going to reload the CCM (but I have to do it out of hours) to see if it solves the problem. Any idea?

Best regards.

5 REPLIES
Silver

Re: MGCP gateway port rejected

I don't think rebooting CCM will resolve the issue. Try to reset the faulty port using "shutdown" and "no shutdown" command under the voice-port. If it doesn't help, unplug the faulty FXS cable and plug it back again.

Make sure you have "service MGCPAPP" configured under dial-peer

ccm-manager mgcp

ccm-manager config server

ccm-manager config

mgcp

mgcp call-agent 2427 service-type mgcp version 0.1

mgcp dtmf-relay voip codec all mode out-of-band

Try to reset the mgcp by using "no mgcp" and then "mgcp":

router(config)#no mgcp

router(config)#mgcp

MK

Re: MGCP gateway port rejected

Thank you for your response. I have tried to reset the port without success. I cannot unplug the cable because I am not phisically in the office where the gateway is installed. The config of MGCP in the gateway is correct (there are seven ports working and one not working in a EVM card). I have try to reset MGCP in the gateway ("no mgcp" and "mgcp"), and I have obtained the same result. Now in RTMT I can see the status reason: DatabaseConfigurationError (before that it showed CallManagerReset).

voice-port 2/0/0

cptone ES

!

voice-port 2/0/1

cptone ES

!

voice-port 2/0/2

cptone ES

!

voice-port 2/0/3

cptone ES

!

voice-port 2/0/4

cptone ES

!

voice-port 2/0/5

cptone ES

!

voice-port 2/0/6

cptone ES

!

voice-port 2/0/7

cptone ES

ccm-manager redundant-host 10.1.80.5

ccm-manager mgcp

ccm-manager music-on-hold

ccm-manager config server 10.50.80.6

ccm-manager config

!

mgcp

mgcp call-agent 10.50.80.6 2427 service-type mgcp version 0.

mgcp rtp unreachable timeout 1000 action notify

mgcp modem passthrough voip mode nse

mgcp package-capability rtp-package

mgcp package-capability sst-package

mgcp package-capability pre-package

no mgcp package-capability res-package

no mgcp package-capability fxr-package

no mgcp timer receive-rtcp

mgcp sdp simple

mgcp rtp payload-type g726r16 static

!

mgcp profile default

dial-peer voice 999200 pots

service mgcpapp

port 2/0/0

!

dial-peer voice 999201 pots

service mgcpapp

port 2/0/1

!

dial-peer voice 999202 pots

service mgcpapp

port 2/0/2

!

dial-peer voice 999203 pots

service mgcpapp

port 2/0/3

!

dial-peer voice 999204 pots

service mgcpapp

port 2/0/4

!

dial-peer voice 999205 pots

service mgcpapp

port 2/0/5

!

dial-peer voice 999206 pots

service mgcpapp

port 2/0/6

!

dial-peer voice 999207 pots

service mgcpapp

port 2/0/7

2/0/0 does not work, 2/0/1-7 work perfectly.

Regards

Re: MGCP gateway port rejected

post this:

debug mgcp packet

voice-p 2/0/0

shut

no shut

-nick

Re: MGCP gateway port rejected

I have done what you say. This is the result:

Mar 19 13:05:17.972: %LINK-3-UPDOWN: Interface Foreign Exchange Station 2/0/0, changed state to Administrative Shutdown

Mar 19 13:05:20.544: MGCP Packet sent to 10.50.80.6:2427--->

NTFY 364027802 *@GW2851Sevilla MGCP 0.1

X: 0

O:

<---

Mar 19 13:05:20.548: MGCP Packet received from 10.50.80.6:2427--->

200 364027802

<---

Mar 19 13:05:21.696: %LINK-3-UPDOWN: Interface Foreign Exchange Station 2/0/0, changed state to up

(10.112.0.1)

Mar 19 13:05:35.544: MGCP Packet sent to 10.50.80.6:2427--->

NTFY 364027803 *@GW2851Sevilla MGCP 0.1

X: 0

O:

<---

Mar 19 13:05:35.548: MGCP Packet received from 10.50.80.6:2427--->

200 364027803

<---

Regards.

Re: MGCP gateway port rejected

Try this for a failed call - this is normal operation. Not very interesting :(

1543
Views
0
Helpful
5
Replies
CreatePlease to create content