Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

MGCP registration

Hi Guys,

I am setting up a couple of fxo ports on an mgcp gateway and for some reason cannot get the ports to register. Here is some output from :

access-hcmc-cs#sh mgcp

MGCP Admin State ACTIVE, Oper State ACTIVE - Cause Code NONE

MGCP call-agent: none Initial protocol service is MGCP 0.1

MGCP validate call-agent source-ipaddr DISABLED

MGCP validate domain name DISABLED

MGCP block-newcalls DISABLED

MGCP send SGCP RSIP: forced/restart/graceful/disconnected DISABLED

MGCP quarantine mode discard/step

MGCP quarantine of persistent events is ENABLED

MGCP dtmf-relay for VoIP is SDP controlled

MGCP dtmf-relay for voAAL2 is SDP controlled

MGCP voip modem passthrough disabled

ccm-manager mgcp

ccm-manager config server 163.184.222.18 163.184.222.34

ccm-manager config

access-hcmc-cs#sh ccm-manager

MGCP Domain Name: access-hcmc-cs.cisco.sinet.slb.com

Priority Status Host

============================================================

Primary None

First Backup None

Second Backup None

Current active Call Manager: None

Backhaul/Redundant link port: 2428

Failover Interval: 30 seconds

Keepalive Interval: 15 seconds

Last keepalive sent: 04:07:12 GMT Jul 14 2008 (elapsed ti

Last MGCP traffic time: 07:50:06 GMT Jul 22 2008 (elapsed ti

)

Last failover time: None

Last switchback time: None

Switchback mode: Graceful

MGCP Fallback mode: Not Selected

Last MGCP Fallback start time: None

Last MGCP Fallback end time: None

MGCP Download Tones: Disabled

TFTP retry count to shut Ports: 2

I can ping the ccm successfully from the gateway and checked the host names etc are a 100% match....any ideas ??

12 REPLIES

Re: MGCP registration

i cant see the following command:

!

mgcp

this command will start the mgcp process

try it

Rate if Helpful

New Member

Re: MGCP registration

Hi,

Sorry i have that already :

!

ccm-manager mgcp

ccm-manager config server X.X.X.X X.X.X.X

ccm-manager config

!

mgcp

Re: MGCP registration

have u made a pots dial-peer for mgcp

lets say ur port number is 1/0/0

dial-peer voice 1 pots

application MGCPAPP

port 1/0/0

New Member

Re: MGCP registration

Hi,

I have not created any dial-peers....is this not something that is downloaded in the xml file from the ccm ???

Re: MGCP registration

try it then let me know

dial peer same as the one above

New Member

Re: MGCP registration

Hi,

The application mgcpapp is not a valid command under the dial-peer....wont allow it...

Re: MGCP registration

you need to bind MGCP to the voice ports. You do this by configuring a dial peer for each voice port and binding MGCP to it using the application MGCPAPP command. This command is case sensitive in some IOS releases. To be safe, code MGCPAPP (all capital letters) unless you know that your release is not case sensitive.

VoiceGW(config)#dial-peer voice 100 pots

VoiceGW(config-dial-peer)#application MGCPAPP

VoiceGW(config-dial-peer)#port 1/0/0

When you make a change to the MGCP configuration, such as adding or changing endpoints, it is a good idea to reinitialize MGCP by issuing no mgcp and then mgcp global configuration commands

source: cisco press, Cisco Voice Gateways and Gatekeepers , 2006

try it agin

and good luck

hope this helpful

VIP Super Bronze

Re: MGCP registration

Have you tried using the command

dial-peer voice 100 pots

service mgcp

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"

Re: MGCP registration

i think service mgcp or application mgcp

he should tell the port that its controlled by the mgcp-agent

right?

VIP Super Bronze

Re: MGCP registration

The service mgcp, enables the MGCP application on the pots dial-peer.

Although in newer versions of IOS, it is not required. It is just safe to have it there

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
New Member

Re: MGCP registration

Pls place output "show running | inclu mgcp" from your rtr.

The output of 'show mgcp' indicated:

****

MGCP call-agent: none

****

It appears no call-agent defined for mgcp.

VIP Super Bronze

Re: MGCP registration

Hi,

ALso have a look at this site. Its the best for MGCP configs

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
238
Views
0
Helpful
12
Replies