Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

MOH doest not works

Hello,

   I have a simple setup with one core 3560 switch with 2 vlans Data 192.168.100.x and Voice 192.168.200.x and CME 4.1 installed on a  router 2801 with an IP address 172.16.0.1 connected to it. My phones are registering well and I am able to call. When I am trying to implement MOH it doesnt works here are the commands which I Have used

telephony-service

moh music-on-hold.au

multicast moh 239.23.4.10 port 2000

your help will be appreciated

11 REPLIES
New Member

MOH doest not works

is is so tough question ??

Hall of Fame Super Silver

Re: MOH doest not works

Do you have multicast enabled on your switch and the voice vlan since it is different network from CME?
Do you have the moh source in flash?

Sent from Cisco Technical Support iPhone App

New Member

Re: MOH doest not works

Hello Chris,

      I havent enabled the Muticast on my switch and the voice vlan. How do I do that ? Do I have to do it on the router  as well.. Yes I have the files in flash..

Re: MOH doest not works

Hi Syed

Can you find the below?. I hope to check if the audio file on the flash.

ip multicast-routing

ccm-manager music-on-hold

CME(config)# telephony-service

CME(config-telephony)#no moh "music-on-hold.au"

CME(config-telephony)# moh flash:music-on-hold.au

CME(config-telephony)# no create cnf-files

CME(config-telephony)#create cnf-files

also find the following URL:-

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmemoh.html#wp1010372

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/feature/guide/MoH.pdf

Thank you

please rate all useful infomation

New Member

MOH doest not works

Thanks Islam,

         I have the file in the flash. Do I have to enable multicast on the router and switch both ?

Hall of Fame Super Silver

Re: MOH doest not works

Yes, if the router is on different vlan than the phones that need to get the multicast moh stream you require multicast routing between the vlans.

Chris

New Member

Re: MOH doest not works

Hello

Try to add ip pum sparse dense mode on the interface going to the switch

Sent from Cisco Technical Support iPhone App

New Member

Re: MOH doest not works

Please see my router configuration and switch configuration. I have done all what mentioned above but still doestn works .

New Member

Re: MOH doest not works

Hello,

    Help !!!!!!!!!!!

MOH doest not works

Hi,

try to do the following on the router:

conf t

ip multicast-routing

!

interface FastEthernet0/0

ip pim dense-mode

!

telephony-service

no multicast moh 239.1.1.10 port 16384

multicast moh 239.1.1.1 port 16384 route 172.16.0.1 172.16.0.2 192.168.200.1

On the switch you'll probably have to insert the ip pim dense-mode commands under the Vlan200 and the Gi0/2 interface as well.

G.

New Member

Re: MOH doest not works

Thanks Greg . Presently I have IP base image on the switch, in order to run the pim command I will have to upgrade it to spservice IOS and do what you mentioned above and let you know.

Thanks

273
Views
0
Helpful
11
Replies