Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

MOH for linksys phone in CME 4.0

I registered 3 SIP phones (linksys)in a CME 4.0 but when I have a call in linksys phone and then put in hold any call I don't listen the music of MOH from the flash.

As far as I know there must be another source for the MOH for linksys phone but I don't know how to set ?

any reference?

4 REPLIES
Hall of Fame Super Red

Re: MOH for linksys phone in CME 4.0

Hi Filiberto,

I think that you require at least CME 4.1 to support MOH on SIP Phones;

Music on Hold for SIP Phones

In Cisco Unified CME 4.1 and later versions, the MOH feature is supported when a call is put on hold from a SIP phone and when the user of a SIP phone is put on hold by a SIP, SCCP, or POTS endpoint. The holder (party that pressed the hold key) or holdee (party who is put on hold) can be on the same Cisco Unified CME or a different Cisco Unified CME connected through a SIP trunk. MOH is also supported for call transfers and conferencing, with or without a transcoding device.

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmemoh.html#wp1010372

Configuring MOH for SIP phones is the same as configuring MOH for SCCP phones. For configuration information, see

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmemoh.html#wp1010384

Hope this helps!

Rob

New Member

Re: MOH for linksys phone in CME 4.0

Hi Rob,

thank you very much for your information

Hall of Fame Super Red

Re: MOH for linksys phone in CME 4.0

Hi Filiberto,

You are most welcome my friend! Have a great day.

Cheers!

Rob

New Member

Re: MOH for linksys phone in CME 4.0

Hi Rob

I have already carried out some test with linksys's phone registerd in CME 4.2 I have the following issues

a) when the holder is a cisco IP phone and the holdee is a linksys phone, MOH works fine

b) when the holder is a linksys phone and the holdee is a cisco IP phone, MOH is not listen.

c) when the holder and holdee are linksys phone I just listen a beep tone.

!

voice register global

mode cme

source-address 10.10.10.1 port 5060

max-dn 5

max-pool 5

timezone 9

date-format D/M/Y

hold-alert

file text

create profile sync 0834091551485355

!

voice register dn 1

number 3251

call-forward b2bua busy 600

call-forward b2bua noan 600 timeout 15

name filo

label 325

!

voice register dn 2

number 3884

name Filo

label 3884

!

voice register dn 3

number 3864

name GeNA

no-reg

label 3864

!

voice register dn 4

number 9745

name Nabor

label 9745

!

voice register dn 5

number 3252

name 3252

label 3252

!

voice register pool 1

id mac 000E.08DE.048A

number 1 dn 1

max registrations 48

dtmf-relay sip-notify

username 3251 password 3251

codec g711ulaw

!

voice register pool 2

id mac 000E.08DF.500D

number 1 dn 2

cor outgoing LADA 1 901

max registrations 48

dtmf-relay sip-notify

username 3884 password 3884

codec g711ulaw

!

!

voice register pool 5

id mac 000E.08D0.4E75

number 1 dn 5

max registrations 48

dtmf-relay sip-notify

username 3252 password 3252

codec g711ulaw

By another hand I set the option of moh in telephony service

telephony-service

moh music-on-hold.au

multicast moh 239.10.16.4 port 2000

I don't know if I have to set something else in linksys phone so that it works fine MOH in all the scenarios.

regards,

209
Views
0
Helpful
4
Replies
CreatePlease to create content