10-23-2007 05:03 AM - edited 03-15-2019 06:58 AM
Hi,
I've a CCM4.3 with several regions ( each regionn with his own h323 gateway ).
Call inside the same region are g.711, calls between different region are g.729.
When arrive a PST call on a region to an IP phone and the phone tranfer the call on another ip-phone IN THE SAME REGION all works fine.
If the call is being tranferred to another REGION does not work ( because the g.729 from different region ).
On the CCM is configured s SW MTP ( the ccm ).
Does I need an IOS MTP or Trancoder ?
Or I've to set the "MTP required" on gateway config ?
I can use c2811 with PVDMII
Any help ?
10-23-2007 12:09 PM
can you post your h323 with dial peer and voice codec class configuration.
I am looking to see if your inbound dial peers that send calls to call manager are set to attempt to use a voice codec class that includes both codecs.
Because in order to transfer from IP Phone to IP Phone no external transcoder is required.
example
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g729br8
codec preference 3 g729r8
!
dial-peer voice 100 voip
description To Call Manager
voice-class codec 1
session target ipv4:
incoming called-number .
no vad
10-24-2007 12:47 AM
Hi,
here the config of the VG; when i Transfer the call to a ip-phone on another region ( talking with the first in G729 ), the ipphone ring-out, but the call go disconnected when the user on that region pickup the call.
...
...
voice class codec 99
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 4 g729r8
codec preference 5 g729br8
codec preference 6 g723ar53
codec preference 7 g723ar63
codec preference 8 g723r53
codec preference 9 g723r63
codec preference 10 g726r16
codec preference 11 g726r24
codec preference 12 g726r32
codec preference 13 g728
...
...
dial-peer voice 2000 voip
destination-pattern 105385T
progress_ind setup enable 3
voice-class codec 99
voice-class h323 99
session target ipv4:10.168.1.1
dtmf-relay h245-alphanumeric
fax rate disable
ip qos dscp cs5 media
ip qos dscp cs3 signaling
!
dial-peer voice 2001 voip
destination-pattern 105385T
progress_ind setup enable 3
voice-class codec 99
session target ipv4:10.168.1.2
dtmf-relay h245-alphanumeric
fax rate disable
ip qos dscp cs5 media
ip qos dscp cs3 signaling
10-24-2007 03:22 AM
Hi,
I've solved the issue using a 2801 with PVDMII64, and configuring transcoding ( see bottom for the config ).
Then I've added to the callmanager as transcoder Cisco IOS Enhanced Media Termination Point.
The only issue is that i see also a lot og G711u transcoding and not only G729.
I already had MTP sotware ( the ccm ), but it seem it does not trancode in G729.
Any suggest ?
regards
Luigi
=====
sccp local FastEthernet0/0
sccp ccm 10.168.1.1 identifier 1 version 4.0
sccp ccm 10.168.1.2 identifier 2 version 4.0
sccp ip precedence 3
sccp
!
sccp ccm group 999
bind interface FastEthernet0/0
associate ccm 1 priority 1
associate ccm 2 priority 2
associate profile 10 register MTP-ios203
keepalive retries 5
switchover method immediate
switchback method immediate
switchback interval 15
!
dspfarm profile 10 transcode
codec g729ar8
codec g729abr8
codec g711ulaw
maximum sessions 24
associate application SCCP
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: